SBOS547A June   2011  – August 2015 INA226

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Basic ADC Functions
        1. 7.3.1.1 Power Calculation
        2. 7.3.1.2 Alert Pin
    4. 7.4 Device Functional Modes
      1. 7.4.1 Averaging and Conversion Time Considerations
      2. 7.4.2 Filtering and Input Considerations
    5. 7.5 Programming
      1. 7.5.1 Programming the Calibration Register
      2. 7.5.2 Programming the Power Measurement Engine
        1. 7.5.2.1 Calibration Register and Scaling
      3. 7.5.3 Simple Current Shunt Monitor Usage (No Programming Necessary)
      4. 7.5.4 Default Settings
      5. 7.5.5 Bus Overview
        1. 7.5.5.1 Serial Bus Address
        2. 7.5.5.2 Serial Interface
        3. 7.5.5.3 Writing to and Reading from the INA226
          1. 7.5.5.3.1 High-Speed I2C Mode
        4. 7.5.5.4 SMBus Alert Response
    6. 7.6 Register Maps
      1. 7.6.1  Configuration Register (00h) (Read/Write)
      2. 7.6.2  Shunt Voltage Register (01h) (Read-Only)
      3. 7.6.3  Bus Voltage Register (02h) (Read-Only)
      4. 7.6.4  Power Register (03h) (Read-Only)
      5. 7.6.5  Current Register (04h) (Read-Only)
      6. 7.6.6  Calibration Register (05h) (Read/Write)
      7. 7.6.7  Mask/Enable Register (06h) (Read/Write)
      8. 7.6.8  Alert Limit Register (07h) (Read/Write)
      9. 7.6.9  Manufacturer ID Register (FEh) (Read-Only)
      10. 7.6.10 Die ID Register (FFh) (Read-Only)
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 High-Side Sensing Circuit Application
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Development Support
    2. 11.2 Community Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

5 Pin Configuration and Functions

DGS Package
10-Pin VSSOP
Top View
INA226 po_msop_bos547.gif

Pin Functions

PIN I/O DESCRIPTION
NAME NO.
A0 2 Digital input Address pin. Connect to GND, SCL, SDA, or VS. Table 2 shows pin settings and corresponding addresses.
A1 1 Digital input Address pin. Connect to GND, SCL, SDA, or VS. Table 2 shows pin settings and corresponding addresses.
Alert 3 Digital output Multi-functional alert, open-drain output.
GND 7 Analog Ground.
IN+ 10 Analog input Connect to supply side of shunt resistor.
IN– 9 Analog input Connect to load side of shunt resistor.
SCL 5 Digital input Serial bus clock line, open-drain input.
SDA 4 Digital I/O Serial bus data line, open-drain input/output.
VBUS 8 Analog input Bus voltage input.
VS 6 Analog Power supply, 2.7 V to 5.5 V.