SLLSE28G October   2010  – October 2015 ISO1176T

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: Power Rating
    6. 6.6  Electrical Characteristics: ISODE-Pin
    7. 6.7  Electrical Characteristics: RS-485 Driver
    8. 6.8  Electrical Characteristics: Receiver
    9. 6.9  Supply Current
    10. 6.10 Transformer Driver Characteristics
    11. 6.11 Switching Characteristics: RS-485 Driver
    12. 6.12 Switching Characteristics: Receiver
    13. 6.13 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Insulation and Safety-Related Specifications for 16-DW Package
      2. 8.3.2 IEC 60664-1 Ratings Table
      3. 8.3.3 DIN V VDE V 0884-10 Insulation Characteristics
      4. 8.3.4 Regulatory Information
      5. 8.3.5 Safety Limiting Values
    4. 8.4 Device Functional Modes
      1. 8.4.1 Device I/O Schematics
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Transient Voltages
      3. 9.2.3 Application Curve
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Community Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ

1 Features

  • Meets or Exceeds the Requirements of EN 50170 and TIA/EIA-485-A
  • Signaling Rates up to 40 Mbps
  • Easy Isolated Power Design with Integrated Transformer Driver
  • Typical Efficiency > 60% (ILOAD = 100 mA) - see SLUU471
  • Differential Output exceeds 2.1 V (54-Ω Load)
  • Low Bus Capacitance 10 pF (Maximum)
  • Fail-safe Receiver for Bus Open, Short, or Idle
  • 50-kV/µs Typical Transient Immunity
  • Safety and Regulatory Approvals
    • 4242 VPK Basic Insulation per DIN V VDE V 0884-10 and DIN EN 61010-1
    • 2500 VRMS Isolation for 1 minute per UL 1577
    • CSA Component Acceptance Notice 5A, IEC 60950-1 and IEC 61010-1 Standards

2 Applications

  • Profibus®
  • Factory Automation
  • Networked Sensors
  • Motor/motion Control
  • HVAC and Building Automation Networks
  • Networked Security Stations

3 Description

The ISO1176T is an isolated differential line transceiver with integrated oscillator outputs that provide the primary voltage for an isolation transformer. The device is ideal for long transmission lines because the ground loop is broken to allow the device to operate with a much larger common-mode voltage range.

The symmetrical isolation barrier of each device is tested to provide 4242VPK of isolation per VDE for 60 seconds between the line transceiver and the logic-level interface.

The galvanically isolated differential bus transceiver is an integrated circuit designed for bi-directional data communication on multipoint bus-transmission lines. The transceiver combines a galvanically isolated differential line driver and differential input line receiver. The driver has an active-high enable with isolated enable-state output on the ISODE pin (pin 10) to facilitate direction control. The driver differential outputs and the receiver differential inputs connect internally to form a differential input/output (I/O) bus port that is designed to offer minimum loading to the bus whenever the driver is disabled or VCC2 = 0.

Any cabled I/O can be subjected to electrical noise transients from various sources. These noise transients can cause damage to the transceiver and/or near-by sensitive circuitry if they are of sufficient magnitude and duration. The ISO1176T can significantly reduce the risk of data corruption and damage to expensive control circuits.

The device is characterized for operation over the ambient temperature range of –40°C to 85°C.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)
ISO1176T SOIC (16) 10.30 mm × 7.50 mm
  1. For all available packages, see the orderable addendum at the end of the datasheet.

Typical Application

ISO1176T ty_app_cir_llse28.gif