SLCS005AA October   1979  – September 2019 LM193 , LM2903 , LM2903B , LM2903V , LM293 , LM293A , LM393 , LM393A , LM393B

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
    1.     Device Images
      1.      Simplified Schematic
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information: LM193
    5. 6.5  Thermal Information: LM293, LM393, LM2903 (all 'V' and 'A' suffixes)
    6. 6.6  Thermal Information: LM393B and LM2903B
    7. 6.7  Electrical Characteristics LM393B
    8. 6.8  Electrical Characteristics LM2903B
    9. 6.9  Switching Characteristics LM393B and LM2903B
    10. 6.10 Electrical Characteristics for LM193, LM293, and LM393 (without A suffix)
    11. 6.11 Electrical Characteristics for LM293A and LM393A
    12. 6.12 Electrical Characteristics for LM2903, LM2903V, and LM2903AV
    13. 6.13 Switching Characteristics (all devices)
    14. 6.14 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
    4. 7.4 Device Functional Modes
      1. 7.4.1 Voltage Comparison
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Input Voltage Range
        2. 8.2.2.2 Minimum Overdrive Voltage
        3. 8.2.2.3 Output and Drive Current
        4. 8.2.2.4 Response Time
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Related Links
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Electrical Characteristics for LM2903, LM2903V, and LM2903AV

at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA(1) LM2903, LM2903V LM2903AV UNIT
MIN TYP MAX MIN TYP MAX
VIO Input offset voltage VCC = 5 V to MAX(2) ,
VO = 1.4 V,
VIC = VICR(min),
25°C 2 7 1 2 mV
Full range 15 4
IIO Input offset current VO = 1.4 V 25°C 5 50 5 50 nA
Full range 200 200
IIB Input bias current VO = 1.4 V 25°C –25 –250 –25 –250 nA
Full range –500 –500
VICR Common-mode input-voltage range(3) 25°C 0 to
VCC – 1.5
0 to
VCC – 1.5
V
Full range 0 to
VCC – 2
0 to
VCC – 2
AVD Large-signal differential-voltage amplification VCC = 15 V, VO = 1.4 V to 11.4 V,
RL ≥ 15 kΩ to VCC
25°C 25 100 25 100 V/mV
IOH High-level output current VOH = 5 V, VID = 1 V 25°C 0.1 50 0.1 50 nA
VOH = VCC MAX(2), VID = 1 V Full range 1 1 µA
VOL Low-level output voltage IOL = 4 mA, VID = –1 V, 25°C 150 400 150 400 mV
Full range 700 700
IOL Low-level output current VOL = 1.5 V, VID = –1 V 25°C 6 6 mA
ICC Supply current RL = ∞ VCC = 5 V 25°C 0.8 1 0.8 1 mA
VCC = MAX Full range 2.5 2.5
Full range (minimum or maximum) for LM2903 is –40°C to 125°C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified.
VCC MAX = 30 V for non-V devices and 32 V for V-suffix devices.
The voltage at either input should not be allowed to go negative by more than 0.3 V otherwise output may be incorrect and excessive input current can flow. The upper end of the common-mode voltage range is limited by VCC – 2V. However only one input needs to be in the valid common mode range, the other input can go up the maximum VCC level and the comparator provides a proper output state. Either or both inputs can go to maximum VCC level without damage.