ホーム パワー・マネージメント バッテリ管理 IC バッテリ・チャージャ IC

BQ24250

アクティブ

SYSOFF モードで 1μA、TS (サーミスタ入力モニタ) ディスエーブル機能搭載、1 セル、2A、I2C 制御、降圧バッテリ・チャージャ

製品詳細

Number of series cells 1 Charge current (max) (A) 2 Vin (max) (V) 10.5 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Absolute max Vin (max) (V) 22 Control topology Switch-Mode Buck Control interface I2C Features BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, Integrated LDO, Power Path Vin (min) (V) 4.35 Rating Catalog Operating temperature range (°C) -40 to 85
Number of series cells 1 Charge current (max) (A) 2 Vin (max) (V) 10.5 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Absolute max Vin (max) (V) 22 Control topology Switch-Mode Buck Control interface I2C Features BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, Integrated LDO, Power Path Vin (min) (V) 4.35 Rating Catalog Operating temperature range (°C) -40 to 85
DSBGA (YFF) 30 5.71999999999999912 mm² 2.2 x 2.5999999999999996 VQFN (RGE) 24 16 mm² 4 x 4
  • High-Efficiency Switched-Mode Charger With
    Separate Power Path
  • Startup System From Deeply Discharged or
    Missing Battery
  • USB Charging Compliant
    • Selectable Input Current Limit of 100 mA,
      500 mA, 900 mA, 1.5 A, and 2 A
  • BC1.2 Compatible D+, D– Detection
  • In Host Mode (After I2C Communication Starts
    and Before Watchdog Timer Times Out)
    • Programmable Battery Charge Voltage,
      VBATREG
    • Programmable Charge Current (ICHG)
    • Programmable Input Current Limit (ILIM)
    • Programmable Input Voltage-Based Dynamic
      Power Management Threshold, (VIN_DPM)
    • Programmable Input Overvoltage Protection
      Threshold (VOVP)
    • Programmable Safety Timer
  • Resistor Programmable Defaults for:
    • ICHG up to 2 A With Current Monitoring Output
      (ISET)
    • ILIM up to 2 A With Current Monitoring Output
      (ILIM)
    • VIN_DPM (VDPM)
  • Watchdog Timer Disable Bit
  • Integrated 4.9 V, 50 mA LDO
  • Complete System-Level Protection
    • Input UVLO, Input Overvoltage Protection
      (OVP), Battery OVP, Sleep Mode, VIN_DPM
    • Input Current Limit
    • Charge Current Limit
    • Thermal Regulation
    • Thermal Shutdown
    • Voltage-Based, JEITA Compatible NTC
      Monitoring Input
    • Safety Timer
  • 22 V Absolute Maximum Input Voltage Rating
  • 10.5 V Maximum Operating Input Voltage
  • Low RDS(on) Integrated Power FETs for a Charging
    Rate of up to 2 A
  • Open-Drain Status Outputs
  • Synchronous Fixed-Frequency PWM Controller
    Operating at 3 MHz for Small Inductor Support
  • AnyBoot Robust Battery Detection Algorithm
  • Charge Time Optimizer for Improved Charge
    Times at Any Given Charge Current
  • 2.40-mm × 2.00-mm 30-Ball DSBGA and 4-mm ×
    4-mm 24-Pin QFN Packages
  • High-Efficiency Switched-Mode Charger With
    Separate Power Path
  • Startup System From Deeply Discharged or
    Missing Battery
  • USB Charging Compliant
    • Selectable Input Current Limit of 100 mA,
      500 mA, 900 mA, 1.5 A, and 2 A
  • BC1.2 Compatible D+, D– Detection
  • In Host Mode (After I2C Communication Starts
    and Before Watchdog Timer Times Out)
    • Programmable Battery Charge Voltage,
      VBATREG
    • Programmable Charge Current (ICHG)
    • Programmable Input Current Limit (ILIM)
    • Programmable Input Voltage-Based Dynamic
      Power Management Threshold, (VIN_DPM)
    • Programmable Input Overvoltage Protection
      Threshold (VOVP)
    • Programmable Safety Timer
  • Resistor Programmable Defaults for:
    • ICHG up to 2 A With Current Monitoring Output
      (ISET)
    • ILIM up to 2 A With Current Monitoring Output
      (ILIM)
    • VIN_DPM (VDPM)
  • Watchdog Timer Disable Bit
  • Integrated 4.9 V, 50 mA LDO
  • Complete System-Level Protection
    • Input UVLO, Input Overvoltage Protection
      (OVP), Battery OVP, Sleep Mode, VIN_DPM
    • Input Current Limit
    • Charge Current Limit
    • Thermal Regulation
    • Thermal Shutdown
    • Voltage-Based, JEITA Compatible NTC
      Monitoring Input
    • Safety Timer
  • 22 V Absolute Maximum Input Voltage Rating
  • 10.5 V Maximum Operating Input Voltage
  • Low RDS(on) Integrated Power FETs for a Charging
    Rate of up to 2 A
  • Open-Drain Status Outputs
  • Synchronous Fixed-Frequency PWM Controller
    Operating at 3 MHz for Small Inductor Support
  • AnyBoot Robust Battery Detection Algorithm
  • Charge Time Optimizer for Improved Charge
    Times at Any Given Charge Current
  • 2.40-mm × 2.00-mm 30-Ball DSBGA and 4-mm ×
    4-mm 24-Pin QFN Packages

The bq24250, bq24251, and bq24253 are highly integrated single-cell Li-Ion battery chargers and system power-path management devices targeted for space-limited, portable applications with high-capacity batteries. The single-cell charger has a single input that operates from either a USB port or an AC wall adapter for a versatile solution.

The power-path management feature allows the bq24250, bq24251, and bq24253 to power the system from a high-efficiency DC-DC converter while simultaneously and independently charging the battery. The charger monitors the battery current at all times and reduces the charge current when the system load requires current above the input current limit. This reduced charge current allows for proper charge termination and enables the system to run with a defective or absent battery pack. Additionally, this reduced charge current enables instant system turnon even with a totally discharged battery or no battery. The architecture of the power-path management also permits the battery to supplement the system current requirements when the adapter cannot deliver the peak system currents. This supplementation of current requirements enables the use of a smaller adapter.

The battery is charged in four phases: trickle charge, precharge, constant current, and constant voltage. In all charge phases, an internal control loop monitors the IC junction temperature and reduces the charge current if the internal temperature threshold is exceeded. Additionally, a voltage-based, JEITA compatible battery pack thermistor monitoring input (TS) that monitors battery temperature for safe charging is included.

The bq24250, bq24251, and bq24253 are highly integrated single-cell Li-Ion battery chargers and system power-path management devices targeted for space-limited, portable applications with high-capacity batteries. The single-cell charger has a single input that operates from either a USB port or an AC wall adapter for a versatile solution.

The power-path management feature allows the bq24250, bq24251, and bq24253 to power the system from a high-efficiency DC-DC converter while simultaneously and independently charging the battery. The charger monitors the battery current at all times and reduces the charge current when the system load requires current above the input current limit. This reduced charge current allows for proper charge termination and enables the system to run with a defective or absent battery pack. Additionally, this reduced charge current enables instant system turnon even with a totally discharged battery or no battery. The architecture of the power-path management also permits the battery to supplement the system current requirements when the adapter cannot deliver the peak system currents. This supplementation of current requirements enables the use of a smaller adapter.

The battery is charged in four phases: trickle charge, precharge, constant current, and constant voltage. In all charge phases, an internal control loop monitors the IC junction temperature and reduces the charge current if the internal temperature threshold is exceeded. Additionally, a voltage-based, JEITA compatible battery pack thermistor monitoring input (TS) that monitors battery temperature for safe charging is included.

ダウンロード 字幕付きのビデオを表示 ビデオ

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと同等の機能で、ピン配置が異なる製品
BQ25611D アクティブ USB 検出機能搭載、1.2A 電流増幅動作、I2C 制御、1 セル、3A 降圧バッテリ・チャージャ This product is 3A, 1S I2C switching buck charger with D+/D- USB detection and programmable JEITA
BQ25618 アクティブ ±20mA 終端と 1A 電流増幅機能搭載、WCSP 封止、I2C 制御、1.5A シングルセル降圧バッテリ・チャージャ This product is 1.5A, 1S I2C buck switching charger with 20mA termination current and programmable JEITA

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
11 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート bq2425x 2A Single-Input I2C, Stand-Alone Switched-Mode Li-Ion Battery Charger With Power-Path Management データシート (Rev. H) PDF | HTML 2015年 8月 20日
セレクション・ガイド 電源 IC セレクション・ガイド 2018 (Rev. R 翻訳版) 英語版 (Rev.R) 2018年 9月 13日
技術記事 TI DLP® NIRscan™ Nano Evaluation Module has answers to your handheld near-infrared PDF | HTML 2015年 10月 2日
製品概要 Battery Management Solutions for Point of Sale Systems 2014年 8月 18日
Analog Design Journal Battery-charging considerations for high-power portable devices 2014年 4月 11日
Analog Design Journal Extract maximum power from the supply when charging a battery 2014年 4月 11日
アプリケーション・ノート Building your own Battery Simulator 2013年 10月 14日
アプリケーション・ノート Using bq2425x’s DPM Feature for Solar Panel Applications 2013年 7月 31日
アプリケーション・ノート Selecting the Best bq2425x Single Cell I2C, Standalone Switch-Mode Battery Charg 2013年 6月 17日
ユーザー・ガイド bq24257EVM-150, Single-Cell Li-Ion Switch-Mode Charger (Rev. A) 2013年 4月 3日
製品概要 Power Bank Charger ICs 2013年 2月 25日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

BOOSTXL-BATPAKMKII — Fuel Tank MKII バッテリ向けブースタパック・プラグイン・モジュール

Fuel Tank MKII BoosterPack™ プラグイン・モジュールは、オリジナルのFuel Tank BoosterPack モジュールに代わる次世代のモジュール製品です。TI の次世代バッテリ監視 IC などの新機能が搭載され、使いやすさが向上しています。Fuel Tank MKII BoosterPack モジュールは、付属の再充電可能なリチウムポリマ・バッテリから TI LaunchPad™ 開発キットに電源を供給し、モバイル・アプリケーションの開発と評価を可能にします。

Fuel Tank MKII BoosterPack (...)

ユーザー ガイド: PDF
評価ボード

BQ24250EVM-150 — BQ24250EVM-150 シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ評価基板

This EVM enables test and evaluation of the Texas Instruments' bq24250/51/57 devices. The bq2425x series are highly integrated single cell Li-Ion battery chargers targeted for space-limited, portable applications with high capacity batteries. The single cell charger has a single input that (...)

ユーザー ガイド: PDF
アプリケーション・ソフトウェアとフレームワーク

TI-CHARGER-GUI — USB2ANY と組み合わせて使用する GUI ソフトウェアと、複数のバッテリ充電評価基板

TI-CHARGER-GUI は、Web ベースまたはスタンドアロンのグラフィカル・ユーザー・インターフェイス (GUI) を実現し、各種バッテリ・チャージャ製品の評価、設計、構成、テストの各プロセスを支援します。このソフトウェアを使用すると、各レジスタへの包括的なアクセスや、コマンドの送信とシーケンス制御用の使いやすいインターフェイスが得られます。
サンプル・コードまたはデモ

BOOSTXL-BATPAKMKII-SW

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
バッテリ・チャージャ IC
BQ24250 SYSOFF モードで 1μA、TS (サーミスタ入力モニタ) ディスエーブル機能搭載、1 セル、2A、I2C 制御、降圧バッテリ・チャージャ
バッテリ残量計
BQ27441-G1 システム側 Impedance Track™ バッテリ残量計
ハードウェア開発
BOOSTXL-BATPAKMKII Fuel Tank MKII バッテリ向けブースタパック・プラグイン・モジュール
ダウンロードオプション
ドライバまたはライブラリ

BQ24257SW-LINUX — Linux ドライバ、BQ24257 用

この Linux ドライバは、スイッチモード・リチウムイオン・バッテリ・チャージャである BQ2425x をサポートしています。また、この Linux ドライバは I2C バス経由の通信をサポートしており、電源サブシステムとのインターフェイスとして機能します。

 

Linux のメインライン・ステータス

Linux メインラインで利用可能か:はい
git.ti.com から入手可能か:N/A

Linux ソース・ファイル

このデバイスに関連付けられているファイル:

  1. drivers/power/supply/bq24257_charger.c
  2. (...)
サポート・ソフトウェア

SLUC435 bq24250EVM Software

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
バッテリ・チャージャ IC
BQ24250 SYSOFF モードで 1μA、TS (サーミスタ入力モニタ) ディスエーブル機能搭載、1 セル、2A、I2C 制御、降圧バッテリ・チャージャ BQ24251 2A、シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ BQ24257 2A、シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ
ハードウェア開発
評価ボード
BQ24250EVM-150 BQ24250EVM-150 シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ評価基板 BQ24251EVM-150 BQ24251EVM-150 シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ評価基板
計算ツール

SLUC436 Thermal TS bq2425x Calculator Tool

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
バッテリ・チャージャ IC
BQ24250 SYSOFF モードで 1μA、TS (サーミスタ入力モニタ) ディスエーブル機能搭載、1 セル、2A、I2C 制御、降圧バッテリ・チャージャ BQ24251 2A、シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ BQ24257 2A、シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ
ハードウェア開発
評価ボード
BQ24250EVM-150 BQ24250EVM-150 シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ評価基板 BQ24251EVM-150 BQ24251EVM-150 シングル入力、I2C/スタンドアロン・スイッチモード・リチウムイオン・バッテリ・チャージャ評価基板
リファレンス・デザイン

TIDA-00554 — Bluetooth 接続のポータブル化学分析用 DLP 超モバイル NIR 分光計

このウルトラモバイル近赤外線(NIR)分光器リファレンス・デザインは TI の DLP テクノロジーと単素子 InGaAs 検出器の組み合わせにより高性能測定を可能にします。高価な InGaAs アレイ検出器や壊れやすい回転回折格子を使用したアーキテクチャとは異なり、低コストでポータブルなフォーム・ファクタを実現します。このリファレンス・デザインは Bluetooth Low Energy に対応しており、食品、農業、製薬、石油化学などのアプリケーション向けのハンドヘルド分光器によるモバイル・ラボ測定を可能にします。TI の Tiva (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDA-00587 — チャージャ・ブースタ・パック、リファレンス・デザイン

The TIDA-00587 reference design is a charger that has been designed as a booster pack to fit on the TI Launchpad development boards. The use of this this board for development will reduce the time spent in design and test of the bq24250 charger IC. You can charger your battery and using the on (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDA-00048 — 2 A、1 入力、I2C/スタンドアロン・スイッチ・モード・リチウムイオン・バッテリ・チャージャ用リファレンス・デザイン

This reference design contains highly integrated single cell Li-Ion battery chargers targeted for space-limited, portable applications with high capacity batteries. The solution includes a single cell charger with a single input that operates from either a USB port or AC wall adapter for a (...)
試験報告書: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
DSBGA (YFF) 30 オプションの表示
VQFN (RGE) 24 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ