ホーム パワー・マネージメント バッテリ管理 IC バッテリ・モニタとバランサ

BQ76PL536A-Q1

アクティブ

車載バッテリ・パック向け、3 ~ 6 個の直列セルのリチウムイオン・バッテリ・モニタと 2 次側保護機能

この製品には新バージョンがあります。

open-in-new 代替品と比較
比較対象デバイスと類似の機能
BQ79616-Q1 アクティブ ASIL-D に準拠した、16S(16 個の直列)車載高精度バッテリ・モニタ、バランサ、統合型プロテクタ 16S/14S/12S Battery Monitor, Balancer and Integrated Hardware Protector in a smaller package (10 mm × 10 mm) and with wider operating temperature (–40°C to +125°C)

製品詳細

Number of series cells (min) 3 Vin (max) (V) 27 Features Cell balancing Device type Cell monitor and balancer Number of series cells (max) 6 Operating temperature range (°C) -40 to 105 Rating Automotive Battery overvoltage protection (min) (V) 2 Battery overvoltage protection (max) (V) 5 Communication interface SPI Operating current (typ) (µA) 10500
Number of series cells (min) 3 Vin (max) (V) 27 Features Cell balancing Device type Cell monitor and balancer Number of series cells (max) 6 Operating temperature range (°C) -40 to 105 Rating Automotive Battery overvoltage protection (min) (V) 2 Battery overvoltage protection (max) (V) 5 Communication interface SPI Operating current (typ) (µA) 10500
HTQFP (PAP) 64 144 mm² 12 x 12
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 2: –40°C to +105°C Ambient Operating Temperature Range
    • Device HBM Classification Level 2
    • Device CDM Classification Level C4B
  • 3-to-6 Series Cell Support, All Chemistries
  • Hot-Pluggable
  • High-Speed Serial Peripheral Interface (SPI) for Data Communications
  • Stackable Vertical Interface
  • Isolation Components Not Required Between Devices
  • High-Accuracy Analog-to-Digital Converter (ADC):
    • ±1 mV Typical Accuracy
    • 14-Bit Resolution, 6-µs Conversion Time
    • Nine ADC Inputs
    • Dedicated Pins for Synchronizing Measurements
  • Configuration Data Stored in Error Check/Correct (ECC)-One-Time-Programmable (OTP) Registers
  • Built-In Comparators (Secondary Protector) for:
    • Overvoltage and Undervoltage Protection
    • Overtemperature Protection
    • Programmable Thresholds and Delay Times
    • Dedicated Fault Signals
  • Cell Balancing Control Outputs With Safety Timeout
    • Balance Current Set by External Components
  • Supply Voltage Range from 7.2 V to 27 V Continuous and 36-V Peak
  • Low Power:
    • Typical 12-µA Sleep, 45-µA Idle
  • Integrated Precision 5-V, 3-mA LDO
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 2: –40°C to +105°C Ambient Operating Temperature Range
    • Device HBM Classification Level 2
    • Device CDM Classification Level C4B
  • 3-to-6 Series Cell Support, All Chemistries
  • Hot-Pluggable
  • High-Speed Serial Peripheral Interface (SPI) for Data Communications
  • Stackable Vertical Interface
  • Isolation Components Not Required Between Devices
  • High-Accuracy Analog-to-Digital Converter (ADC):
    • ±1 mV Typical Accuracy
    • 14-Bit Resolution, 6-µs Conversion Time
    • Nine ADC Inputs
    • Dedicated Pins for Synchronizing Measurements
  • Configuration Data Stored in Error Check/Correct (ECC)-One-Time-Programmable (OTP) Registers
  • Built-In Comparators (Secondary Protector) for:
    • Overvoltage and Undervoltage Protection
    • Overtemperature Protection
    • Programmable Thresholds and Delay Times
    • Dedicated Fault Signals
  • Cell Balancing Control Outputs With Safety Timeout
    • Balance Current Set by External Components
  • Supply Voltage Range from 7.2 V to 27 V Continuous and 36-V Peak
  • Low Power:
    • Typical 12-µA Sleep, 45-µA Idle
  • Integrated Precision 5-V, 3-mA LDO

The bq76PL536A-Q1 device is a stackable battery monitor and protector for three-to-six lithium-ion cells in series. The bq76PL536A-Q1 integrates an analog front end (AFE) along with a precision analog-to-digital converter (ADC), used to precisely measure battery cell voltages. A separate ADC is used to measure temperature.

In addition to temperature measurement, overvoltage and undervoltage are monitored per channel for protection. Non-volatile memory stores the user-programmable protection thresholds and delay times. A FAULT output signals whenever one of these thresholds is exceeded.

Cell stacks of 192 cells can be supported by stacked bq76PL536A-Q1 devices. A high-speed SPI interface connects all devices.

The bq76PL536A-Q1 device is a stackable battery monitor and protector for three-to-six lithium-ion cells in series. The bq76PL536A-Q1 integrates an analog front end (AFE) along with a precision analog-to-digital converter (ADC), used to precisely measure battery cell voltages. A separate ADC is used to measure temperature.

In addition to temperature measurement, overvoltage and undervoltage are monitored per channel for protection. Non-volatile memory stores the user-programmable protection thresholds and delay times. A FAULT output signals whenever one of these thresholds is exceeded.

Cell stacks of 192 cells can be supported by stacked bq76PL536A-Q1 devices. A high-speed SPI interface connects all devices.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
7 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート bq76PL536A-Q1 3-to-6 Series Cell Lithium-Ion Battery Monitor and Secondary Protection IC for EV and HEV Applications データシート (Rev. A) PDF | HTML 2016年 12月 12日
アプリケーション・ノート Designing EMI/EMC Safe Battery Pack 2016年 6月 14日
技術記事 How batteries may make travel on Mars easier PDF | HTML 2016年 1月 27日
ユーザー・ガイド bq76PL536A and bq76PL536A-Q1 EVM Quick Start Guide (Rev. D) 2015年 7月 28日
アプリケーション・ノート bq76PL536/536A/536AQ1 Communication Basics (Rev. B) 2011年 7月 5日
アプリケーション・ノート Multi-Cell Li-Ion Battery Management System Using MSP430F5529 and bq76PL536 2010年 12月 16日
アプリケーション・ノート Improving Communications With the bq76PL536 2010年 8月 11日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

BQ76PL536EVM-3 — 評価モジュール、BQ76PL536 用、リチウムイオン・バッテリー・モニタ/ 2 次保護 IC

BQ76PL536EVM-3, Evaluation Module for the BQ76PL536A/bq76PL536A-Q1 Lithium-Ion Battery Monitor and Secondary Protection IC. The User’s Guide document covers the initial connection and installation of the Texas Instruments bq76PL536A/bq76PL536A-Q1 Evaluation Module (EVM), supplied in kit form (...)

ユーザー ガイド: PDF
サポート・ソフトウェア

BQ76PL536EVM-3-SW — BQ76PL536EVM-3 ソフトウェア

The BQ76PL536EVM-3 tool interfaces with the bq76PL536EVM-3 evaluation board
パッケージ ピン数 ダウンロード
HTQFP (PAP) 64 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ