車載対応、3 相ゲート ドライバ

DRV8301-Q1 は新規設計での使用を推奨しません
従来の設計をサポートできるようにこの製品は引き続き生産中ですが、TI はこの製品を新規の設計には推奨しません。以下の代替品のいずれかをご検討ください。
open-in-new 代替品と比較
比較対象デバイスと類似の機能
DRV8343-Q1 アクティブ 車載対応、電流シャント・アンプ搭載、12V ~ 24V バッテリ、3 相スマート・ゲート・ドライバ DRV8343-Q1 supports up to 60 V input voltage and has 3 current-sense amplifiers

製品詳細

Rating Automotive Architecture Gate driver Operating temperature range (°C) -40 to 125
Rating Automotive Architecture Gate driver Operating temperature range (°C) -40 to 125
HTSSOP (DCA) 56 113.4 mm² 14 x 8.1
  • Qualified for Automotive Applications
  • AEC-Q100 Tested With the Following Results:
    • Device Temperature Grade 1: –40°C to 125°C
      Ambient Operating Temperature Range
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4A
  • Operating Supply Voltage 6 to 60 V
  • 2.3-A Sink and 1.7-A Source Gate Drive Current
    Capability
  • Integrated Dual Shunt Current Amplifiers With
    Adjustable Gain and Offset
  • Integrated Buck Converter to Support up to 1.5-A
    External Load
  • Independent Control of 3 or 6 PWM Inputs
  • Bootstrap Gate Driver With 100% Duty Cycle
    Support
  • Programmable Dead Time to Protect External
    FETs from Shoot-Through
  • Slew Rate Control for EMI Reduction
  • Programmable Overcurrent Protection of External
    MOSFETs
  • Support Both 3.3-V and 5-V Digital Interface
  • SPI Interface
  • Thermally Enhanced 56-Pin HTSSOP Pad-Down
    DCA Package
  • Qualified for Automotive Applications
  • AEC-Q100 Tested With the Following Results:
    • Device Temperature Grade 1: –40°C to 125°C
      Ambient Operating Temperature Range
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4A
  • Operating Supply Voltage 6 to 60 V
  • 2.3-A Sink and 1.7-A Source Gate Drive Current
    Capability
  • Integrated Dual Shunt Current Amplifiers With
    Adjustable Gain and Offset
  • Integrated Buck Converter to Support up to 1.5-A
    External Load
  • Independent Control of 3 or 6 PWM Inputs
  • Bootstrap Gate Driver With 100% Duty Cycle
    Support
  • Programmable Dead Time to Protect External
    FETs from Shoot-Through
  • Slew Rate Control for EMI Reduction
  • Programmable Overcurrent Protection of External
    MOSFETs
  • Support Both 3.3-V and 5-V Digital Interface
  • SPI Interface
  • Thermally Enhanced 56-Pin HTSSOP Pad-Down
    DCA Package

The DRV8301-Q1 device is an automotive gate driver IC for three phase motor drive applications. The device provides three half bridge drivers, each capable of driving two N-type MOSFETs, one for the high-side and one for the low side. The device supports up to 2.3-A sink and 1.7-A source peak current capability and only needs a single power supply with a wide range from 6 to 60 V. The DRV8301-Q1 device uses bootstrap gate drivers with trickle charge circuitry to support 100% duty cycle. The gate driver uses automatic hand shaking when high-side FET or low-side FET is switching to prevent current shoot through. VDS of FETs is sensed to protect external power stage during overcurrent conditions.

The DRV8301-Q1 device includes two current shunt amplifiers for accurate current measurement. The current amplifiers support bi-directional current sensing and provide an adjustable output offset of up to 3 V.

The DRV8301-Q1 device also has an integrated switching mode buck converter with adjustable output and switching frequency to support MCU or additional system power needs. The buck is capable to drive up to 1.5-A load.

The SPI interface provides detailed fault reporting and flexible parameter settings such as gain options for current shunt amplifier, slew rate control of gate driver, and other settings.

The DRV8301-Q1 device is an automotive gate driver IC for three phase motor drive applications. The device provides three half bridge drivers, each capable of driving two N-type MOSFETs, one for the high-side and one for the low side. The device supports up to 2.3-A sink and 1.7-A source peak current capability and only needs a single power supply with a wide range from 6 to 60 V. The DRV8301-Q1 device uses bootstrap gate drivers with trickle charge circuitry to support 100% duty cycle. The gate driver uses automatic hand shaking when high-side FET or low-side FET is switching to prevent current shoot through. VDS of FETs is sensed to protect external power stage during overcurrent conditions.

The DRV8301-Q1 device includes two current shunt amplifiers for accurate current measurement. The current amplifiers support bi-directional current sensing and provide an adjustable output offset of up to 3 V.

The DRV8301-Q1 device also has an integrated switching mode buck converter with adjustable output and switching frequency to support MCU or additional system power needs. The buck is capable to drive up to 1.5-A load.

The SPI interface provides detailed fault reporting and flexible parameter settings such as gain options for current shunt amplifier, slew rate control of gate driver, and other settings.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
3 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート DRV8301-Q1 Automotive Three-Phase Gate Driver With Dual Current Shunt Amplifiers and Buck Regulator データシート (Rev. A) PDF | HTML 2015年 6月 30日
アプリケーション・ノート Hardware Design Considerations for an Electric Bicycle using BLDC Motor (Rev. B) 2021年 6月 23日
アプリケーション・ノート Hardware Design Considerations for an Efficient Vacuum Cleaner Using a BLDC Moto (Rev. B) PDF | HTML 2019年 3月 6日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

リファレンス・デザイン

TIDA-00143 — 車載用 60W ブラシレス DC(BLDC)モータ・ドライブ

TIDA-00143 は、BLDC モーター・コントローラのリファレンス・デザインで、単一の 12V(公称)電源で動作が可能で、車載機器で必要な、非常に広い電圧範囲での変動にも対応できます。ボードは、5 アンペアの電流が必要なモーターを 60Wレンジで駆動します。ボードはサイズとレイアウト面で、駆動用電子回路とファームウェアの評価を容易にするよう設計されており、個々のテスト・ポイント上の重要な信号へのアクセスも可能です。3 点コネクタを使用するか、モーターの位相配線をボードのめっきスルーホールにハンダ付けすることで、さまざまなタイプのモーターへの接続が可能です。12Vdc (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDM-RM46XDRV8301KIT — 高性能マイコン付き 3 相 BLDC / PMSM モータ・ドライブ・リファレンス・デザイン

このリファレンス・デザインは、永久磁石シンクロナス・モーター (PMSM) とも呼ばれる、三相ブラシレス DC およびブラシレス AC (BLAC) モーターの回転用のモーター制御用評価キットです。センサレス・フィールド・オリエンテッド / ベクトル制御 (FOC) のサンプルが付属しています。実装には、DRV8301 ゲート・ドライバ IC と TPS65381 パワー・マネージメント IC (PMIC) を活用します。このリファレンス・デザインは、高性能、高い電力効率、コスト効率の優れたプラットフォームとして使用され、PMSM 制御アルゴリズムの開発を迅速化できます。
設計ガイド: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
HTSSOP (DCA) 56 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ