DRV8846

アクティブ

1/32 マイクロステップ機能とスマート・チューニング・アダプティブ減衰機能を搭載した、18V、1.4A のバイポーラ・ステッパ・モーター・ドライバ

製品詳細

Number of full bridges 2 Vs (min) (V) 4 Vs ABS (max) (V) 20 Full-scale current (A) 1 Peak output current (A) 2 RDS(ON) (HS + LS) (mΩ) 900 Sleep current (µA) 1.2 Control mode STEP/DIR Control interface Hardware (GPIO) Microstepping levels 32 Features Current Regulation, Smart Tune Rating Catalog Operating temperature range (°C) -40 to 85
Number of full bridges 2 Vs (min) (V) 4 Vs ABS (max) (V) 20 Full-scale current (A) 1 Peak output current (A) 2 RDS(ON) (HS + LS) (mΩ) 900 Sleep current (µA) 1.2 Control mode STEP/DIR Control interface Hardware (GPIO) Microstepping levels 32 Features Current Regulation, Smart Tune Rating Catalog Operating temperature range (°C) -40 to 85
VQFN (RGE) 24 16 mm² 4 x 4
  • PWM Microstepping Motor Driver
    • Built-In Microstepping Indexer
    • Up to 1/32 Microstepping
    • Step/Direction Control
  • Multiple Decay Modes
    • Smart tune Technology
    • Mixed Decay
    • Slow Decay
    • Fast Decay
  • Configurable Off-Time PWM Chopping
    • 10-, 20-, or 30-µs Off-Time
  • Adaptive Blanking Time for Smooth Stepping
  • 4- to 18-V Operating Supply Voltage Range
  • 1.4-A (Full Scale (Max Drive) Current per H-Bridge (at 25°C)
  • Low-Current Sleep Mode
  • 3-Bit Torque DAC to Scale Motor Current
  • Thermally Enhanced Surface Mount Package
  • Protection Features
    • VM Undervoltage Lockout (UVLO)
    • Overcurrent Protection (OCP)
    • Thermal Shutdown (TSD)
    • Fault Condition Indication Pin (nFAULT)
  • PWM Microstepping Motor Driver
    • Built-In Microstepping Indexer
    • Up to 1/32 Microstepping
    • Step/Direction Control
  • Multiple Decay Modes
    • Smart tune Technology
    • Mixed Decay
    • Slow Decay
    • Fast Decay
  • Configurable Off-Time PWM Chopping
    • 10-, 20-, or 30-µs Off-Time
  • Adaptive Blanking Time for Smooth Stepping
  • 4- to 18-V Operating Supply Voltage Range
  • 1.4-A (Full Scale (Max Drive) Current per H-Bridge (at 25°C)
  • Low-Current Sleep Mode
  • 3-Bit Torque DAC to Scale Motor Current
  • Thermally Enhanced Surface Mount Package
  • Protection Features
    • VM Undervoltage Lockout (UVLO)
    • Overcurrent Protection (OCP)
    • Thermal Shutdown (TSD)
    • Fault Condition Indication Pin (nFAULT)

The DRV8846 provides a highly-integrated stepper motor driver for cameras, printers, projectors, and other automated equipment applications. The device has two H-bridges and a microstepping indexer and is intended to drive a bipolar stepper motor. The output block of each H-bridge driver consists of N-channel and P-channel power MOSFETs configured as full H-bridges to drive the motor windings. The DRV8846 is capable of driving up to 1.4-A full-scale output current (with proper heatsinking and TA = 25°C).

A simple STEP/DIR interface allows easy interfacing to controller circuits. Pins allow configuration of the motor in full-step up to 1/32-step modes. Decay mode is configurable so that smart tune, slow decay, fast decay, and mixed decay can be used. The PWM current chopping off-time can also be selected. A low-power sleep mode is provided which shuts down internal circuitry to achieve very-low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin.

Internal protection functions are provided for UVLO, overcurrent protection, short circuit protection, and overtemperature. Fault conditions are indicated via a nFAULT pin.

The DRV8846 provides a highly-integrated stepper motor driver for cameras, printers, projectors, and other automated equipment applications. The device has two H-bridges and a microstepping indexer and is intended to drive a bipolar stepper motor. The output block of each H-bridge driver consists of N-channel and P-channel power MOSFETs configured as full H-bridges to drive the motor windings. The DRV8846 is capable of driving up to 1.4-A full-scale output current (with proper heatsinking and TA = 25°C).

A simple STEP/DIR interface allows easy interfacing to controller circuits. Pins allow configuration of the motor in full-step up to 1/32-step modes. Decay mode is configurable so that smart tune, slow decay, fast decay, and mixed decay can be used. The PWM current chopping off-time can also be selected. A low-power sleep mode is provided which shuts down internal circuitry to achieve very-low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin.

Internal protection functions are provided for UVLO, overcurrent protection, short circuit protection, and overtemperature. Fault conditions are indicated via a nFAULT pin.

ダウンロード 字幕付きのビデオを表示 ビデオ

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと同等の機能で、ピン配置が異なる製品
DRV8428 アクティブ 電流センシング機能と 1/256 マイクロステップ機能を統合した、35V、1A のバイポーラ・ステッパ・モーター・ドライバ Higher voltage support
DRV8834 アクティブ 1/32 マイクロステップ インデクサ搭載、11V、1.5A、デュアル、H ブリッジまたはステッパ モーターのドライバ Lower voltage support

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
9 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート DRV8846 Dual H-Bridge Stepper Motor Driver データシート (Rev. A) PDF | HTML 2017年 3月 27日
アプリケーション・ノート モーター・ドライバ向け基板レイアウト事例 (Rev. B 翻訳版) PDF | HTML 英語版 (Rev.B) PDF | HTML 2021年 10月 14日
アプリケーション・ノート Methods to Configure Current Regulation for Brushed and Stepper Motors (Rev. B) PDF | HTML 2021年 1月 19日
ホワイト・ペーパー How smart tune regulates current in stepper motors (Rev. A) 2019年 3月 19日
アプリケーション概要 Smart Tuning for Efficient Stepper Driving 2018年 11月 20日
アプリケーション概要 Small Motors in Large Appliances 2018年 7月 20日
技術記事 Spin your stepper automatically PDF | HTML 2016年 3月 3日
その他の技術資料 TM4C123x Stepper Motor Control Product Summary 2015年 7月 6日
EVM ユーザー ガイド (英語) DRV8846 Evaluation Module User Guide (Rev. A) 2015年 3月 18日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

DRV8846EVM — DRV8846 デュアル・ハーフ・ブリッジ ステッパ・モーター・ドライバの評価モジュール

The DRV8846 is a highly integrated stepper motor controller and driver for cameras, printers, projectors, and other automated equipment applications.This device has been optimized to drive a single bipolar stepper with up to 1/32 microstepping with on-chip indexers.

The DRV8846EVM is a platform (...)

ユーザー ガイド: PDF
リファレンス・デザイン

TIDA-00405 — 3D プリンタ・コントローラ(12V)

この設計は、3 軸、シングル・エクストルーダ(射出成形機)ベースの 3D プリンタを制御するための包括的なシステムです。このシステムは MSP430F5529 ローンチパッドの管理下で、DRV8846 を使用してステッパ・モーターを高精度制御します。CSD18534Q5A は、ホット・ベッド(ヒート・ベッド)ヒーター、エクストルーダー・ヒーター、および冷却ファンのローサイド・スイッチとして使用します。DRV5033 ホール・センサは、非接触型制限スイッチとして機能します。
試験報告書: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
VQFN (RGE) 24 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ