DRV8873

アクティブ

電流センシング機能と電流センス・フィードバック機能内蔵、40V、10A の H ブリッジ・モーター・ドライバ

製品詳細

Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 150 Sleep current (µA) 15 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Rating Catalog Operating temperature range (°C) -40 to 125
Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 150 Sleep current (µA) 15 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Rating Catalog Operating temperature range (°C) -40 to 125
HTSSOP (PWP) 24 49.92 mm² 7.8 x 6.4
  • H-Bridge Motor Driver
    • Drives One DC Motor, One Winding of a Stepper Motor, or Solenoid Loads
  • 4.5-V to 38-V Operating Voltage Range
  • 10-A Peak Current Drive
  • Low HS + LS RDS(ON)
    • 150 mΩ at TJ = 25°C, 13.5 V
    • 250 mΩ at TJ = 150°C, 13.5 V
  • Current Mirror for Output Current Sensing
  • Configurable Control Interface
    • PH/EN
    • PWM (IN1/IN2)
    • Independent Half-Bridge Control
  • Supports 1.8-V, 3.3-V, 5-V Logic Inputs
  • SPI or Hardware Interface Options
  • Low-Power Sleep Mode (10 µA)
  • Small Package and Footprint
    • 24 HTSSOP PowerPAD™ IC Package
  • Protection Features
    • VM Undervoltage Lockout (UVLO)
    • Charge Pump Undervoltage (CPUV)
    • Overcurrent Protection (OCP)
    • Output short to battery and short to ground protection
    • Open Load Detection
    • Thermal Shutdown (TSD)
    • Fault Condition Output (nFAULT / SPI)
  • H-Bridge Motor Driver
    • Drives One DC Motor, One Winding of a Stepper Motor, or Solenoid Loads
  • 4.5-V to 38-V Operating Voltage Range
  • 10-A Peak Current Drive
  • Low HS + LS RDS(ON)
    • 150 mΩ at TJ = 25°C, 13.5 V
    • 250 mΩ at TJ = 150°C, 13.5 V
  • Current Mirror for Output Current Sensing
  • Configurable Control Interface
    • PH/EN
    • PWM (IN1/IN2)
    • Independent Half-Bridge Control
  • Supports 1.8-V, 3.3-V, 5-V Logic Inputs
  • SPI or Hardware Interface Options
  • Low-Power Sleep Mode (10 µA)
  • Small Package and Footprint
    • 24 HTSSOP PowerPAD™ IC Package
  • Protection Features
    • VM Undervoltage Lockout (UVLO)
    • Charge Pump Undervoltage (CPUV)
    • Overcurrent Protection (OCP)
    • Output short to battery and short to ground protection
    • Open Load Detection
    • Thermal Shutdown (TSD)
    • Fault Condition Output (nFAULT / SPI)

The DRV8873 device is an integrated driver IC for driving a brushed DC motor in industrial applications. Two logic inputs control the H-bridge driver, which consists of four N-channel MOSFETs that drive motors bi-directionally with up to 10-A peak current. The device operates from a single power supply and supports a wide input supply range from 4.5 V to 38 V.

A PH/EN or PWM interface allows simple interfacing to controller circuits. Alternatively, independent half-bridge control is available to drive two solenoid loads.

A current mirror allows the controller to monitor the load current. This mirror approximates the current through the high-side FETs, and does not require a high-power resistor for sensing the current.

A low-power sleep mode is provided to achieve very-low quiescent current draw by shutting down much of the internal circuitry. Internal protection functions are provided for undervoltage lockout, charge pump faults, overcurrent protection, short-circuit protection, open-load detection, and overtemperature. Fault conditions are indicated on an nFAULT pin and through the SPI registers.

The DRV8873 device is an integrated driver IC for driving a brushed DC motor in industrial applications. Two logic inputs control the H-bridge driver, which consists of four N-channel MOSFETs that drive motors bi-directionally with up to 10-A peak current. The device operates from a single power supply and supports a wide input supply range from 4.5 V to 38 V.

A PH/EN or PWM interface allows simple interfacing to controller circuits. Alternatively, independent half-bridge control is available to drive two solenoid loads.

A current mirror allows the controller to monitor the load current. This mirror approximates the current through the high-side FETs, and does not require a high-power resistor for sensing the current.

A low-power sleep mode is provided to achieve very-low quiescent current draw by shutting down much of the internal circuitry. Internal protection functions are provided for undervoltage lockout, charge pump faults, overcurrent protection, short-circuit protection, open-load detection, and overtemperature. Fault conditions are indicated on an nFAULT pin and through the SPI registers.

ダウンロード 字幕付きのビデオを表示 ビデオ

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと類似の機能
DRV8256 アクティブ 電流センス機能内蔵、スマート・チューン・テクノロジー採用、50V、8A、H ブリッジ・モーター・ドライバ 48V, 8A H-Bridge Motor Driver With Integrated Current Sense and Smart Tune Technology

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
12 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート DRV8873 H-Bridge Motor Driver データシート PDF | HTML 2018年 6月 11日
証明書 DRV8873HEVM EU Declaration of Conformity (DoC) 2023年 7月 12日
証明書 DRV8873SEVM EU Declaration of Conformity (DoC) 2023年 7月 11日
アプリケーション概要 Advantages of Integrated Current Sensing (Rev. B) PDF | HTML 2022年 6月 20日
アプリケーション・ノート Using DRV to Drive Solenoids (Rev. A) PDF | HTML 2022年 4月 24日
アプリケーション・ノート Daisy Chain Implementation for Serial Peripheral Interface (Rev. A) 2021年 4月 7日
技術記事 Overcoming design challenges for brushed-DC motors in smart sanitation systems PDF | HTML 2020年 7月 1日
技術記事 Helping physicians achieve faster, more accurate patient diagnoses with molecular PDF | HTML 2020年 5月 20日
技術記事 Automating smart home blinds, shades and shutters with motor drivers PDF | HTML 2020年 1月 2日
アプリケーション概要 Small Motors in Large Appliances 2018年 7月 20日
アプリケーション・ノート PowerPAD™ Thermally Enhanced Package (Rev. H) 2018年 7月 6日
アプリケーション概要 PowerPAD™ Made Easy (Rev. B) 2004年 5月 12日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

DRV8873HEVM — ハードウェア・インターフェイスと統合型電流センシング機能搭載、10A H ブリッジ・モーター・ドライバの評価モジュール

DRV8873 は産業 / 車載アプリケーション向けの統合型ドライバです。10A のピーク電流能力と 4.5 ~ 38V の電圧範囲を提供し、広範なアプリケーションに対応します。PH/EN または PWM インターフェイスによりコントローラ回路に容易にインターフェイスするとともに、独立したハーフ・ブリッジ制御機能により 2 個のソレノイド負荷を駆動します。

電流ミラーがハイサイド FET に流れる電流の近似値を示すことから、センス抵抗が不要です。

低消費電力スリープ・モードにより内部回路の大部分をシャットダウンし、静止電流を大幅に低減します。

(...)

ユーザー ガイド: PDF
評価ボード

DRV8873SEVM — ハードウェア・インターフェイスと統合型電流センシング機能搭載、10A H ブリッジ・モーター・ドライバの評価モジュール

The DRV8873 is an integrated driver for industrial and automotive applications. With 10 A peak current capability and 4.5-38V voltage range, this device supports a wide range of applications.

PH/EN or PWM interface allows simple interfacing to controller circuits while also allowing independent (...)

ユーザー ガイド: PDF
パッケージ ピン数 ダウンロード
HTSSOP (PWP) 24 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ