ホーム パワー・マネージメント DC/DC スイッチング・レギュレータ 降圧 (バック) レギュレータ 降圧 コントローラ (外部スイッチ)

4.5V ~ 30V、2 相、ピーク電流モード、同期整流降圧コントローラ

この製品には新バージョンがあります。

open-in-new 代替品と比較
比較対象デバイスと類似の機能
TPS51397A アクティブ 4.5V ~ 24V 入力、10A の同期整流降圧レギュレータ Upgraded current rating with light-load efficiency and is soft start adjustable.

製品詳細

Vin (min) (V) 4.5 Vin (max) (V) 30 Vout (min) (V) 1.238 Vout (max) (V) 27 Iout (max) (A) 6 Iq (typ) (mA) 1 Switching frequency (min) (kHz) 300 Switching frequency (max) (kHz) 300 Features Adjustable current limit, Enable, Phase Interleaving, Power good, Synchronous Rectification Operating temperature range (°C) -40 to 125 Regulated outputs (#) 2 Number of phases 2 Rating Catalog Control mode current mode Type Controller
Vin (min) (V) 4.5 Vin (max) (V) 30 Vout (min) (V) 1.238 Vout (max) (V) 27 Iout (max) (A) 6 Iq (typ) (mA) 1 Switching frequency (min) (kHz) 300 Switching frequency (max) (kHz) 300 Features Adjustable current limit, Enable, Phase Interleaving, Power good, Synchronous Rectification Operating temperature range (°C) -40 to 125 Regulated outputs (#) 2 Number of phases 2 Rating Catalog Control mode current mode Type Controller
TSSOP (PW) 28 62.08 mm² 9.7 x 6.4
  • Two synchronous buck regulators
  • 180° out of phase operation
  • 4.5V to 30V input range
  • Power good function monitors Ch.1
  • 37µA Shutdown current
  • 0.04% (typical) line and load regulation error
  • Current mode control with or without a sense resistor
  • Independent enable/soft-start pins allow simple sequential startup configuration.
  • Configurable for single output parallel operation. (See ).
  • Adjustable cycle-by-cycle current limit
  • Input under-voltage lockout
  • Output over-voltage latch protection
  • Output under-voltage protection with delay
  • Thermal shutdown
  • Self discharge of output capacitors when the regulator is OFF
  • TSSOP package

  • Two synchronous buck regulators
  • 180° out of phase operation
  • 4.5V to 30V input range
  • Power good function monitors Ch.1
  • 37µA Shutdown current
  • 0.04% (typical) line and load regulation error
  • Current mode control with or without a sense resistor
  • Independent enable/soft-start pins allow simple sequential startup configuration.
  • Configurable for single output parallel operation. (See ).
  • Adjustable cycle-by-cycle current limit
  • Input under-voltage lockout
  • Output over-voltage latch protection
  • Output under-voltage protection with delay
  • Thermal shutdown
  • Self discharge of output capacitors when the regulator is OFF
  • TSSOP package

The LM2642 consists of two current mode synchronous buck regulator controllers with a switching frequency of 300kHz.

The two switching regulator controllers operate 180° out of phase. This feature reduces the input ripple RMS current, thereby significantly reducing the required input capacitance. The two switching regulator outputs can also be paralleled to operate as a dual-phase single output regulator.

The output of each channel can be independently adjusted from 1.3 to VIN• maximum duty cycle. An internal 5V rail is also available externally for driving bootstrap circuitry.

Current-mode feedback control assures excellent line and load regulation and a wide loop bandwidth for excellent response to fast load transients. Current is sensed across either the Vds of the top FET or across an external current-sense resistor connected in series with the drain of the top FET. Current limit is independently adjustable for each channel.

The LM2642 features analog soft-start circuitry that is independent of the output load and output capacitance. This makes the soft-start behavior more predictable and controllable than traditional soft-start circuits.

A PGOOD1 pin is provided to monitor the dc output of channel 1. Over-voltage protection is available for both outputs. A UV-Delay pin is also available to allow delayed shut off time for the IC during an output under-voltage event.


The LM2642 consists of two current mode synchronous buck regulator controllers with a switching frequency of 300kHz.

The two switching regulator controllers operate 180° out of phase. This feature reduces the input ripple RMS current, thereby significantly reducing the required input capacitance. The two switching regulator outputs can also be paralleled to operate as a dual-phase single output regulator.

The output of each channel can be independently adjusted from 1.3 to VIN• maximum duty cycle. An internal 5V rail is also available externally for driving bootstrap circuitry.

Current-mode feedback control assures excellent line and load regulation and a wide loop bandwidth for excellent response to fast load transients. Current is sensed across either the Vds of the top FET or across an external current-sense resistor connected in series with the drain of the top FET. Current limit is independently adjustable for each channel.

The LM2642 features analog soft-start circuitry that is independent of the output load and output capacitance. This makes the soft-start behavior more predictable and controllable than traditional soft-start circuits.

A PGOOD1 pin is provided to monitor the dc output of channel 1. Over-voltage protection is available for both outputs. A UV-Delay pin is also available to allow delayed shut off time for the IC during an output under-voltage event.


ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
6 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート LM2642 Two-Phase Synchronous Step-Down Switching Controller (jp) データシート (Rev. H 翻訳版) 最新英語版 (Rev.I) PDF | HTML 2006年 2月 15日
ユーザー・ガイド LM2642 Buck Controller Evaluation Module User's Guide (Rev. I) PDF | HTML 2022年 1月 25日
セレクション・ガイド 電源 IC セレクション・ガイド 2018 (Rev. R 翻訳版) 英語版 (Rev.R) 2018年 9月 13日
Analog Design Journal Reduce buck-converter EMI and voltage stress by minimizing inductive parasitics 2016年 7月 21日
Analog Design Journal Controlling switch-node ringing in synchronous buck converters 2012年 4月 26日
アプリケーション・ノート Application Note 1239 LM2642 Evaluation Board (jp) 2006年 3月 23日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
パッケージ ピン数 ダウンロード
TSSOP (PW) 28 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ