TLC555-Q1
- AEC-Q100 qualified for automotive applications:
- Temperature grade 1: –40°C to +125°C, TA
- Functional Safety-Capable
- Very-low power consumption
- 1mW (typical) at VDD = 5V
- Capable of operation in astable mode
- CMOS output capable of swinging rail to rail
- High-output-current capability
- Sink 100mA (typical)
- Source 10mA (typical)
- Output fully compatible with CMOS, TTL, and MOS
- Low supply current reduces spikes during output transitions
- Single-supply operation from 2V to 15V
- Temperature range: –40°C to +125°C
- Functionally interchangeable with the NE555; has same pinout
The TLC555-Q1 is a monolithic timing circuit fabricated using TI LinCMOS™ technology. The timer is fully compatible with CMOS, TTL, and MOS logic and operates at frequencies up to 2MHz. As a result of the high input impedance, this device supports smaller timing capacitors than capacitors used by the NE555. Thus, more accurate time delays and oscillations are possible. Power consumption is low across the full power-supply voltage range.
Like the NE555, the TLC555-Q1 has a trigger level equal to approximately one-third of the supply voltage, and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by using the control voltage pin (CONT). When the trigger input (TRIG) falls below the trigger level, the flip-flop is set, and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output goes low. The reset input (RESET) can override all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output goes low. Whenever the output is low, a low-impedance path is provided between the discharge pin (DISCH) and GND. Tie all unused inputs to an appropriate logic level to prevent false triggering.
技術資料
種類 | タイトル | 最新の英語版をダウンロード | 日付 | |||
---|---|---|---|---|---|---|
* | データシート | TLC555-Q1 Automotive LinCMOS™ Technology Timer データシート (Rev. C) | PDF | HTML | 2024年 4月 17日 | ||
機能安全情報 | TLC555-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA (Rev. A) | PDF | HTML | 2023年 3月 13日 | |||
技術記事 | Power Tips: Multiply your output voltage | PDF | HTML | 2016年 7月 20日 | |||
設計ガイド | EMC Compatible Automotive LED Rear Lamp Sequential-Turn Animation Design Guide | 2016年 6月 2日 | ||||
アプリケーション・ノート | TLC555-Q1 Used as a Positive and Negative Charge Pump | 2016年 5月 25日 |
設計と開発
その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。
TLC555 TINA-TI Astable Reference Design (Rev. B)
TLC555 TINA-TI Mono Reference Design (Rev. B)
PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®
設計とシミュレーション向けの環境である PSpice for TI (...)
パッケージ | ピン数 | ダウンロード |
---|---|---|
SOIC (D) | 8 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL 定格 / ピーク リフロー
- MTBF/FIT 推定値
- 材質成分
- 認定試験結果
- 継続的な信頼性モニタ試験結果
- ファブの拠点
- 組み立てを実施した拠点
推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。