TPIC2050

アクティブ

3 ビームのレーザー ダイオード ドライバ搭載、シリアル インターフェイス制御、9 チャネル、モーター ドライバ

製品詳細

Applications 4K Ultra HD, Blu-ray, CD, DVD Motor driver channels 9 Integrated supply 3 laser diode drivers Operating supply (V) 5 Driver supply voltage (V) 12 Operating temperature range (°C) -20 to 75 Rating Catalog
Applications 4K Ultra HD, Blu-ray, CD, DVD Motor driver channels 9 Integrated supply 3 laser diode drivers Operating supply (V) 5 Driver supply voltage (V) 12 Operating temperature range (°C) -20 to 75 Rating Catalog
HTSSOP (DFD) 56 113.4 mm² 14 x 8.1
  • Serial Port Digital Interface
    • Serial Peripheral Interface (SPI)
    • 4-Wire Interface: SSZ, SCLK, SIMO, SOMI
    • Maximum Read/Write 35 MHz
    • 3.3-V Digital I/O
  • Actuator and Motor Driver
    • PWM Control With H-Bridge Output
    • Focus / Tracking / Tilt Actuator Driver With 12-Bit DAC Control
    • Sled Motor Drivers With Current Mode, 10-Bit DAC Control
    • Load Driver With 12-Bit DAC Control Selectable 5 V, 12 V
    • Stepping Motor Driver With 8-Bit PWM Control
  • Spindle Motor Driver
    • Low Rdson 0.3-Ω Typical MOSFET Output
    • Sensor-Less: Rotor Position Sense by Motor BEMF
    • Applicable for 10500 rpm Revolution Speed (Assumed in Using 12-Pole Motor)
    • 12-Bit Spindle DAC Programmed Via Serial Port
    • Self-Contained Inductive Position Sense and Startup
    • Auto-Brake Function Which Selects the Optimal Brake Mode in Each Rotation Speed
    • 1.5-A Maximum Continuous Current Excluding Thermal Issues
  • Utility Functions
    • Status Latch: Act Timer, SIF Error, PWR Monitor, Thermal Protection, and OCP Error
    • On-Chip Thermometer (15 to 165°C)
  • 3-Beam Laser Diode Driver
    • 120-mA Current Output With 11-Bit DAC Register or Analog Input (VLDDIN)
    • Slope-Controlled Current for Rapid Change
    • Select Output Port of CD, DVD, BD by Serial Bit
  • Protection
    • Individual Thermal Protect Circuit on SPM and Actuator Driver
    • Two Alert Levels: Pre-Detect and Detect in Thermal Protection
    • ACTTEMP: Monitor the Actuator Temperature Calculated from Integrating the DAC Value Set Up in the Past
    • Short-Circuit Protection in SPM, Sled, Load, Actuator, and Step-Driver Channel
    • Hardware Device Disable Pin, XRSTIN
    • Power Monitor by Undervoltage Lockout (UVLO) and Overvoltage Protection (OVP)
    • Tray-Lock Detection
    • PREOVP-12V: Prevent the 12-V OVP Detection by the Motor BEMF at SPM Brake
  • Serial Port Digital Interface
    • Serial Peripheral Interface (SPI)
    • 4-Wire Interface: SSZ, SCLK, SIMO, SOMI
    • Maximum Read/Write 35 MHz
    • 3.3-V Digital I/O
  • Actuator and Motor Driver
    • PWM Control With H-Bridge Output
    • Focus / Tracking / Tilt Actuator Driver With 12-Bit DAC Control
    • Sled Motor Drivers With Current Mode, 10-Bit DAC Control
    • Load Driver With 12-Bit DAC Control Selectable 5 V, 12 V
    • Stepping Motor Driver With 8-Bit PWM Control
  • Spindle Motor Driver
    • Low Rdson 0.3-Ω Typical MOSFET Output
    • Sensor-Less: Rotor Position Sense by Motor BEMF
    • Applicable for 10500 rpm Revolution Speed (Assumed in Using 12-Pole Motor)
    • 12-Bit Spindle DAC Programmed Via Serial Port
    • Self-Contained Inductive Position Sense and Startup
    • Auto-Brake Function Which Selects the Optimal Brake Mode in Each Rotation Speed
    • 1.5-A Maximum Continuous Current Excluding Thermal Issues
  • Utility Functions
    • Status Latch: Act Timer, SIF Error, PWR Monitor, Thermal Protection, and OCP Error
    • On-Chip Thermometer (15 to 165°C)
  • 3-Beam Laser Diode Driver
    • 120-mA Current Output With 11-Bit DAC Register or Analog Input (VLDDIN)
    • Slope-Controlled Current for Rapid Change
    • Select Output Port of CD, DVD, BD by Serial Bit
  • Protection
    • Individual Thermal Protect Circuit on SPM and Actuator Driver
    • Two Alert Levels: Pre-Detect and Detect in Thermal Protection
    • ACTTEMP: Monitor the Actuator Temperature Calculated from Integrating the DAC Value Set Up in the Past
    • Short-Circuit Protection in SPM, Sled, Load, Actuator, and Step-Driver Channel
    • Hardware Device Disable Pin, XRSTIN
    • Power Monitor by Undervoltage Lockout (UVLO) and Overvoltage Protection (OVP)
    • Tray-Lock Detection
    • PREOVP-12V: Prevent the 12-V OVP Detection by the Motor BEMF at SPM Brake

The TPIC2050 is low-noise-type motor driver IC suitable for 12-V ODD. The 9-channel driver, IC controlled by serial interface, is optimum for driving a spindle motor, sled motor (stepping motor applicable), load motor, focus / tracking / tilt actuators, and stepping motor for the collimator lens.

The spindle motor driver part builds in the sensor-less logic that attains low-noise operation at start-up and while running. Motors or sensors, such as a Hall device, are not required by the starting circuit for self-starting, or for performing position detection by BEMF. As the output stage of all channels works in efficient PWM driving, low-power operation by PWM control is possible. Neutral zone-less control is possible for a focus / tracking / tilt actuator driver. In addition, the spindle part output current limiting circuit, thermal shutdown circuit, sled-end detection circuit, collimator lens end detection circuit, actuator protection, and three beam laser drivers are built in. The newly added built-in thermometer can measure IC temperature.

The TPIC2050 is low-noise-type motor driver IC suitable for 12-V ODD. The 9-channel driver, IC controlled by serial interface, is optimum for driving a spindle motor, sled motor (stepping motor applicable), load motor, focus / tracking / tilt actuators, and stepping motor for the collimator lens.

The spindle motor driver part builds in the sensor-less logic that attains low-noise operation at start-up and while running. Motors or sensors, such as a Hall device, are not required by the starting circuit for self-starting, or for performing position detection by BEMF. As the output stage of all channels works in efficient PWM driving, low-power operation by PWM control is possible. Neutral zone-less control is possible for a focus / tracking / tilt actuator driver. In addition, the spindle part output current limiting circuit, thermal shutdown circuit, sled-end detection circuit, collimator lens end detection circuit, actuator protection, and three beam laser drivers are built in. The newly added built-in thermometer can measure IC temperature.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
1 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート TPIC2050 Serial I/F Controlled 9-Channel Motor-Driver With 3-Beam Laser Diode Driver データシート PDF | HTML 2015年 8月 10日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

パッケージ ピン数 ダウンロード
HTSSOP (DFD) 56 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ