ホーム パワー・マネージメント DC/DC スイッチング・レギュレータ 昇圧 (ブースト) レギュレータ 昇圧コンバータ (スイッチ内蔵)

TPS61291

アクティブ

15nA バイパス動作、低静止電流 (Iq) 昇圧コンバータ

製品詳細

Topology Boost Vin (min) (V) 0.9 Vin (max) (V) 5 Vout (min) (V) 2.5 Vout (max) (V) 3.3 Switch current limit (typ) (A) 1 Type Converter Regulated outputs (#) 1 Switching frequency (min) (kHz) 2300 Switching frequency (max) (kHz) 2300 Iq (typ) (mA) 0.005 Features Bypass Mode Pass-through Mode, Synchronous Rectification Duty cycle (max) (%) 90 Operating temperature range (°C) -40 to 125 Rating Catalog
Topology Boost Vin (min) (V) 0.9 Vin (max) (V) 5 Vout (min) (V) 2.5 Vout (max) (V) 3.3 Switch current limit (typ) (A) 1 Type Converter Regulated outputs (#) 1 Switching frequency (min) (kHz) 2300 Switching frequency (max) (kHz) 2300 Iq (typ) (mA) 0.005 Features Bypass Mode Pass-through Mode, Synchronous Rectification Duty cycle (max) (%) 90 Operating temperature range (°C) -40 to 125 Rating Catalog
WSON (DRV) 6 4 mm² 2 x 2
  • Input Voltage Range 0.9V to 5V
  • Startup Voltage 1.5V at 20mA Load
  • Pin Selectable Output Voltages:
    3.3V, 3V, 2.5V
  • 15nA typical Quiescent Current in
    Bypass Mode
  • 5.7µA typical Quiescent Current in
    Boost Mode
  • Bypass Switch from VIN to VOUT
  • IOUT > 200mA at 3.3V VOUT,
    VIN = 1.8V
  • Internal Feedback Divider Disconnect
    (Bypass Mode)
  • Controlled Bypass Transition Prevents
    Reverse Current into Battery
  • Power-Save Mode at Light Loads
  • Overtemperature Protection
  • Redundant Overvoltage Protection
  • Small 2mm × 2mm SON 6-pin package
  • Input Voltage Range 0.9V to 5V
  • Startup Voltage 1.5V at 20mA Load
  • Pin Selectable Output Voltages:
    3.3V, 3V, 2.5V
  • 15nA typical Quiescent Current in
    Bypass Mode
  • 5.7µA typical Quiescent Current in
    Boost Mode
  • Bypass Switch from VIN to VOUT
  • IOUT > 200mA at 3.3V VOUT,
    VIN = 1.8V
  • Internal Feedback Divider Disconnect
    (Bypass Mode)
  • Controlled Bypass Transition Prevents
    Reverse Current into Battery
  • Power-Save Mode at Light Loads
  • Overtemperature Protection
  • Redundant Overvoltage Protection
  • Small 2mm × 2mm SON 6-pin package

The TPS61291 is a boost converter with pin selectable output voltages and an integrated bypass mode. In bypass operation, the device provides a direct path from the input to the system and allows a low power micro controller (MCU) such as the MSP430 to operate directly from a single 3V Li-MnO2 battery or dual alkaline battery cells.

In bypass mode the integrated feedback divider network for boost mode operation is disconnected from the output and the quiescent current consumption drops down to only 15nA (typical).

In boost mode the device provides a minimum output current of 200mA at 3.3V VOUT from 1.8V VIN. The boost mode is used for system components which require a regulated supply voltage and cannot directly operate from the input source. The boost converter is based on a current-mode controller using synchronous rectification to obtain maximum efficiency and consumes typically 5.7µA from the output. During startup of the boost converter, the VSEL pin is read out and the integrated feedback network sets the output voltage to 2.5V, 3V or 3.3V.

Bypass mode or boost mode operation is controlled by the system via the EN/BYP pin.

The device integrates an enhanced bypass mode control to prevent charge, stored in the output capacitor during boost mode operation, from flowing back to the input and charging the battery.

The device is packaged in a small 6-pin SON package (DRV) measuring 2.0mm × 2.0mm × 0.75mm.

The TPS61291 is a boost converter with pin selectable output voltages and an integrated bypass mode. In bypass operation, the device provides a direct path from the input to the system and allows a low power micro controller (MCU) such as the MSP430 to operate directly from a single 3V Li-MnO2 battery or dual alkaline battery cells.

In bypass mode the integrated feedback divider network for boost mode operation is disconnected from the output and the quiescent current consumption drops down to only 15nA (typical).

In boost mode the device provides a minimum output current of 200mA at 3.3V VOUT from 1.8V VIN. The boost mode is used for system components which require a regulated supply voltage and cannot directly operate from the input source. The boost converter is based on a current-mode controller using synchronous rectification to obtain maximum efficiency and consumes typically 5.7µA from the output. During startup of the boost converter, the VSEL pin is read out and the integrated feedback network sets the output voltage to 2.5V, 3V or 3.3V.

Bypass mode or boost mode operation is controlled by the system via the EN/BYP pin.

The device integrates an enhanced bypass mode control to prevent charge, stored in the output capacitor during boost mode operation, from flowing back to the input and charging the battery.

The device is packaged in a small 6-pin SON package (DRV) measuring 2.0mm × 2.0mm × 0.75mm.

ダウンロード 字幕付きのビデオを表示 ビデオ

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと同等の機能で、ピン配置が異なる製品
TPS61094 アクティブ バイパス・モード搭載、60nA 静止電流、双方向昇降圧コンバータ 60-nA quiescent current bi-directional buck/boost converter with bypass mode
NEW TPS61299 アクティブ 入力電流制限機能搭載、高速過渡特性、95nA、低静止電流 (IQ)、5.5V 昇圧コンバータ Lower IQ, true disconnect and higher IOUT
比較対象デバイスと類似の機能
TPS610981 アクティブ LDO 内蔵、低入力電圧、3.3V の出力電圧、同期整流昇圧コンバータ For applications requiring ultra-low Iq or smaller package.
TPS61220 アクティブ 5.5μA の静止電流、0.7VIN、調整可能な出力電圧、昇圧コンバータ For applications requiring ultra-low Iq or smaller package.

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
12 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート TPS61291 Low Iq Boost Converter with Bypass Operation データシート (Rev. A) PDF | HTML 2014年 9月 23日
アプリケーション・ノート QFN and SON PCB Attachment (Rev. C) PDF | HTML 2023年 12月 6日
アプリケーション・ノート 昇圧コンバータの電力段に関する基本的な計算 (Rev. D 翻訳版) PDF | HTML 英語版 (Rev.D) PDF | HTML 2022年 12月 1日
アプリケーション・ノート Basic Calculation of a Boost Converter's Power Stage... (Rev. D) PDF | HTML 2022年 11月 21日
アプリケーション・ノート Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018年 12月 11日
アプリケーション・ノート Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 2017年 6月 15日
アプリケーション・ノート Calculating and Measuring the No Load Input Current of the Boost Converter 2016年 9月 23日
技術記事 How to use boost converters in wireless sensor nodes PDF | HTML 2015年 10月 6日
EVM ユーザー ガイド (英語) TPS61291EVM-569 Evaluation Module 2014年 9月 17日
Analog Design Journal Accurately measuring efficiency of ultralow-IQ devices 2014年 1月 22日
Analog Design Journal IQ: What it is, what it isn’t, and how to use it 2011年 6月 17日
アプリケーション・ノート Minimizing Ringing at the Switch Node of a Boost Converter 2006年 9月 15日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

TPS61291EVM-569 — 低 IQ 昇圧コンバータ 評価モジュール、バイパス・モード付き

The TPS61291EVM-569 facilitates the evaluation of the TPS61291 Low IQ Boost Converter with Bypass Mode device.  The device outputs a user-selectable output voltage of 2.5V, 3V, or 3.3V.  Available output current depends on the input voltage and output voltage but is generally around 200 (...)

ユーザー ガイド: PDF
シミュレーション・モデル

Unencrypted TPS61291 PSpice Transient Model Package (Rev. A)

SLVMAD5A.ZIP (22 KB) - PSpice Model
ガーバー・ファイル

TPS61291EVM-569 Gerbers

SLVC574.ZIP (176 KB)
シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
リファレンス・デザイン

TIDM-ULTRASONIC-FLOW-TDC — 超音波 TDC 流量計、リファレンス・デザイン

The TIDM-ULTRASONIC-FLOW-TDC is a reference design for an ultrasonic flow meter (water, gas or heat meter) with LCD built using a Time-to-Digital converter and an ultra-low power MCU. Solution includes optimized leakage detection, low power consumption, and a small form factor that are (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDA-00484 — 湿度および温度センサ・ノード、1 GHz 以下のスター型ネットワーク用、コイン型電池の 10 年以上の寿命を実現

このリファレンス・デザインは、 TI のナノパワー・システム・タイマ、昇圧コンバータ、SimpleLink™ 超低消費電力 Sub-1GHz ワイヤレス・マイコン (MCU) プラットフォーム、湿度センシング技術を組み合わせて、センサのエンド・ノードのデューティ・サイクル動作を超低消費電力で実現する方法を提示し、非常に長いバッテリ動作期間に寄与します。このデザインは、システム設計の手法、詳細なテスト結果、迅速な設計開始と推進に役立つ情報も公開しています。
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDA-01469 — 予知保全を可能にするワイヤレス振動センサ使用モーター監視のリファレンス・デザイン

This reference design is a low-power wireless subsystem solution that monitors motors using vibration sensing to determine if preventative maintenance is necessary. An FFT of the vibration data can be sent out to another device using either Bluetooth low energy or sub-1GHz wireless protocols. The (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

TIDA-01477 — Sub-1GHz とセンサ / クラウド間ネットワークを可能にする温湿度センサ・ノードのリファレンス・デザイン

This reference design demonstrates how to create an industrial sensor-to-cloud end node capable of connecting to an IoT network gateway and a cloud data provider. This sensor node reference design uses Texas Instruments' nano-power system timer for power gating, low Iq boost converter, (...)
設計ガイド: PDF
回路図: PDF
リファレンス・デザイン

PMP9763 — スマート・メータ・パワー・マネージメント・ソリューション、エネルギ・バッファ付、リファレンス・デザイン

Smart Wireless Sensors are typically powered by Long-Life Batteries Like LiSoCl2 chemistry which are limited in current. However, these sensors require high current pulses for transmitting the gathered data wirelessly. This Reference Design provides a solution for powering the MCU with reduced (...)
試験報告書: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
WSON (DRV) 6 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ