ホーム パワー・マネージメント LCD / OLED ディスプレイ向けの電源とドライバ

TPS65131-Q1

アクティブ

車載向け、デュアル、正出力と負出力 (代表値 750mA)、分割レール・コンバータ

製品詳細

Display type LCD bipolar IC integration LCD bias Vin (min) (V) 2.7 Vin (max) (V) 5.5 Applications 7 inches or less, 7 to 13 inches Source driver voltage (min) (V) -15 Source driver voltage (max) (V) 15 Level shifter/scan driver (Ch) 0 V_POS (min) (V) 3.2 V_POS (max) (V) 15 V_NEG (min) (V) -15 V_NEG (max) (V) -2 Features Adjustable sequencing Topology Split-Rail Rating Automotive Operating temperature range (°C) -40 to 105
Display type LCD bipolar IC integration LCD bias Vin (min) (V) 2.7 Vin (max) (V) 5.5 Applications 7 inches or less, 7 to 13 inches Source driver voltage (min) (V) -15 Source driver voltage (max) (V) 15 Level shifter/scan driver (Ch) 0 V_POS (min) (V) 3.2 V_POS (max) (V) 15 V_NEG (min) (V) -15 V_NEG (max) (V) -2 Features Adjustable sequencing Topology Split-Rail Rating Automotive Operating temperature range (°C) -40 to 105
VQFN (RGE) 24 16 mm² 4 x 4
  • Qualified for Automotive Applications
  • AEC-Q100 Test Guidance With the Following Results:
    • Device Temperature Grade 2: –40°C to 105°C Ambient Operating Temperature Range
    • Electrical Characteristics Tested Over –40°C to 125°C Junction Temperature Range
    • Device HBM ESD Classification Level H1C
    • Device CDM ESD Classification Level C4B
  • Dual Adjustable Output Voltages up to 15 V and down to –15 V
  • 2–A Typical Switch-Current Limit for Boost and Inverter Main Switches
  • High Conversion Efficiency
    • Up to 91% at Positive Output Rail
    • Up to 85% at Negative Output Rail
    • Power-Save Mode at Low Load
  • Independent Enable Inputs for Power-Up and Power-Down Sequencing
  • Control Output for External PFET to Support Complete Supply Disconnect When Shut Down
  • 2.7-V to 5.5-V Input-Voltage Range
  • Minimum 1.25-MHz Fixed-Frequency PWM Operation
  • Thermal Shutdown
  • Overvoltage Protection on Both Outputs
  • 0.2-µA Typical Shutdown Current
  • Small 4-mm × 4-mm QFN-24 Package (RGE)
  • Qualified for Automotive Applications
  • AEC-Q100 Test Guidance With the Following Results:
    • Device Temperature Grade 2: –40°C to 105°C Ambient Operating Temperature Range
    • Electrical Characteristics Tested Over –40°C to 125°C Junction Temperature Range
    • Device HBM ESD Classification Level H1C
    • Device CDM ESD Classification Level C4B
  • Dual Adjustable Output Voltages up to 15 V and down to –15 V
  • 2–A Typical Switch-Current Limit for Boost and Inverter Main Switches
  • High Conversion Efficiency
    • Up to 91% at Positive Output Rail
    • Up to 85% at Negative Output Rail
    • Power-Save Mode at Low Load
  • Independent Enable Inputs for Power-Up and Power-Down Sequencing
  • Control Output for External PFET to Support Complete Supply Disconnect When Shut Down
  • 2.7-V to 5.5-V Input-Voltage Range
  • Minimum 1.25-MHz Fixed-Frequency PWM Operation
  • Thermal Shutdown
  • Overvoltage Protection on Both Outputs
  • 0.2-µA Typical Shutdown Current
  • Small 4-mm × 4-mm QFN-24 Package (RGE)

The TPS65131-Q1 device is dual-output dc-dc converter generating a positive output voltage up to 15 V and a negative output voltage down to –15 V with output currents of typically 200 mA, depending on input-voltage to output-voltage ratio. With a total efficiency up to 85%, the device is ideal for portable battery-powered equipment. The input-voltage range of 2.7 V to 5.5 V allows, for example, 3.3-V and 5-V rails to power the TPS65131-Q1 device. The TPS65131-Q1 device comes in a QFN-24 package with thermal pad. Requiring few and small external components, the overall solution size can be small.

The converter operates with a fixed-frequency PWM control topology and, with power-save mode enabled, uses a pulse-skipping mode at light load currents. In operation, the typical overall device quiescent current is only 500 µA. In shutdown, the device draws typically 0.2 µA. Independent enable pins allow power-up and power-down sequencing for both outputs. The device has an internal current limit, overvoltage protection, and a thermal shutdown for highest reliability under fault conditions.

The TPS65131-Q1 device is qualified for automotive applications, according to AEC-Q100 temperature grade 2. The electrical characteristics are tested over –40°C to 125°C device junction temperature. This, combined with lowest shutdown currents, small solution size, package with thermal pad, plus good efficiency and protection features, targets automotive and industrial applications.

The TPS65131-Q1 device is dual-output dc-dc converter generating a positive output voltage up to 15 V and a negative output voltage down to –15 V with output currents of typically 200 mA, depending on input-voltage to output-voltage ratio. With a total efficiency up to 85%, the device is ideal for portable battery-powered equipment. The input-voltage range of 2.7 V to 5.5 V allows, for example, 3.3-V and 5-V rails to power the TPS65131-Q1 device. The TPS65131-Q1 device comes in a QFN-24 package with thermal pad. Requiring few and small external components, the overall solution size can be small.

The converter operates with a fixed-frequency PWM control topology and, with power-save mode enabled, uses a pulse-skipping mode at light load currents. In operation, the typical overall device quiescent current is only 500 µA. In shutdown, the device draws typically 0.2 µA. Independent enable pins allow power-up and power-down sequencing for both outputs. The device has an internal current limit, overvoltage protection, and a thermal shutdown for highest reliability under fault conditions.

The TPS65131-Q1 device is qualified for automotive applications, according to AEC-Q100 temperature grade 2. The electrical characteristics are tested over –40°C to 125°C device junction temperature. This, combined with lowest shutdown currents, small solution size, package with thermal pad, plus good efficiency and protection features, targets automotive and industrial applications.

ダウンロード 字幕付きのビデオを表示 ビデオ

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと類似の機能
TPS65100-Q1 アクティブ 車載向け、昇圧コンバータとデュアル・チャージ・ポンプと LDO コントローラ搭載、2.7V ~ 5.8V LCD 電源 This product is an LCD supply with integrated VGH, VGL, Vcom, LDO and works with displays requiring +AVDD (instead of +/-AVDD).
TPS65150-Q1 アクティブ 車載向け、VCOM (電圧補償機能) バッファ内蔵、コンパクト LCD バイアス電源 This product uses +AVDD (instead of +/-AVDD), and integrates VGH, VGL, and Vcom.

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
9 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート TPS65131-Q1 Positive- and Negative-Output DC-DC Converter データシート (Rev. E) PDF | HTML 2017年 2月 8日
アプリケーション・ノート 昇圧コンバータの電力段に関する基本的な計算 (Rev. D 翻訳版) PDF | HTML 英語版 (Rev.D) PDF | HTML 2022年 12月 1日
アプリケーション・ノート Basic Calculation of a Boost Converter's Power Stage... (Rev. D) PDF | HTML 2022年 11月 21日
アプリケーション・ノート Understanding Undervoltage Lockout in Power Devices (Rev. A) 2018年 9月 19日
ホワイト・ペーパー Powering automotive displays to create interactive driving experiences 2017年 12月 21日
アプリケーション・ノート Basic calculation of an inverting buck-boost power stage (Rev. A) 2017年 8月 28日
技術記事 Split-rail converters reduce BOM size and cost in new automotive displays PDF | HTML 2015年 7月 1日
EVM ユーザー ガイド (英語) TPS65131EVM User's Guide (Rev. C) 2010年 11月 23日
アプリケーション・ノート Minimizing Ringing at the Switch Node of a Boost Converter 2006年 9月 15日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
リファレンス・デザイン

PMP9780 — リファレンス・デザイン:バイポーラ TFT LCD 電源、TPS65131-Q1 およびチャージ・ポンプ使用

このリファレンス・デザインは、ソース・ドライバ用のバイポーラ電圧レールと、ゲート・ドライバ用の付加的な電源を生成する、ディスプレイ向け電源回路のためのリファレンス・デザインです。チャージ・ポンプを使用してゲート・ドライバ用の電源電圧を生成しているので、このデザインの実装は容易です。DC/DC コンバータを 1 個だけ使用して 4 つの電圧レールを生成しているので、インダクタンスの総量が最小化されており、この回路でデザイン・サイズを小型化することができます。
試験報告書: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
VQFN (RGE) 24 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ