TS3USB30E
- VCC Operation at 3 V to 4.3 V
- D+/D– Pins Tolerate up to 5.25 V
- 1.8-V Compatible Control-Pin Inputs
- IOFF Supports Partial Power-Down-Mode
Operation - RON = 10 Ω Maximum
- ΔRON = 0.35 Ω Typical
- Cio(ON) = 7.5 pF Typical
- Low Power Consumption (1 µA Maximum)
- –3-dB Bandwidth = 900 MHz Typical
- Latch-Up Performance Exceeds
100 mA Per JESD 78, Class II(1) - ESD Performance Tested Per JESD 22
- 8000-V Human-Body Model
(A114-B, Class II) - 1000-V Charged-Device Model (C101)
- 8000-V Human-Body Model
- ESD Performance I/O Port to GND(2)
- 15000-V Human-Body Model
- Packaged in 10-pin UQFN (1.4 mm × 1.8 mm)
The TS3USB30E is a high-bandwidth 1:2 switch specially designed for the switching of high-speed USB 2.0 signals in handset and consumer applications, such as cell phones, digital cameras, and notebooks with hubs or controllers with limited USB I/Os. The wide bandwidth (900 MHz) of this switch allows signals to pass with minimum edge and phase distortion. The device multiplexes differential outputs from a USB host device to one of two corresponding outputs, or from two different hosts to one corresponding output. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation, and is compatible with various standards, such as high-speed USB 2.0 (480 Mbps).
The TS3USB30E integrates ESD protection cells on all pins, is available in a tiny UQFN package (1.8 mm × 1.4 mm) or a VSSOP package, and is characterized over the free-air temperature range of 40°C to 85°C.
技術資料
種類 | タイトル | 最新の英語版をダウンロード | 日付 | |||
---|---|---|---|---|---|---|
* | データシート | ESD-Protected, High-Speed USB 2.0 (480-Mbps) 1:2 Multiplexer/Demultiplexer Swit データシート (Rev. F) | 2015年 8月 14日 | |||
アプリケーション・ノート | Passive Mux Selection Based On Bandwidth > Ron | 2019年 9月 11日 | ||||
アプリケーション・ノート | High-Speed Layout Guidelines for Signal Conditioners and USB Hubs | 2018年 6月 14日 |
設計と開発
その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。
PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®
設計とシミュレーション向けの環境である PSpice for TI (...)
TINA-TI — SPICE ベースのアナログ・シミュレーション・プログラム
TINA-TI をインストールするには、約 500MB が必要です。インストールは簡単です。必要に応じてアンインストールも可能です。(そのようなことはないと思いますが)
TINA は DesignSoft (...)
パッケージ | ピン数 | ダウンロード |
---|---|---|
UQFN (RSW) | 10 | オプションの表示 |
VSSOP (DGS) | 10 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL 定格 / ピーク リフロー
- MTBF/FIT 推定値
- 材質成分
- 認定試験結果
- 継続的な信頼性モニタ試験結果
- ファブの拠点
- 組み立てを実施した拠点
推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。