ホーム パワー・マネージメント ゲート・ドライバ ローサイド・ドライバ

UCC27532

アクティブ

8V UVLO、35V VDD 対応、複数の CMOS 入力、分割出力対応、2.5A/5A、シングルチャネル・ゲート・ドライバ

製品詳細

Number of channels 1 Power switch IGBT, MOSFET, SiCFET Peak output current (A) 5 Input supply voltage (min) (V) 10 Input supply voltage (max) (V) 32 Features Split Output Operating temperature range (°C) -40 to 140 Rise time (ns) 15 Fall time (ns) 7 Propagation delay time (µs) 0.017 Input threshold CMOS Channel input logic Non-Inverting, Single Input negative voltage (V) -5 Rating Catalog Undervoltage lockout (typ) (V) 8 Driver configuration Non-Inverting, Single
Number of channels 1 Power switch IGBT, MOSFET, SiCFET Peak output current (A) 5 Input supply voltage (min) (V) 10 Input supply voltage (max) (V) 32 Features Split Output Operating temperature range (°C) -40 to 140 Rise time (ns) 15 Fall time (ns) 7 Propagation delay time (µs) 0.017 Input threshold CMOS Channel input logic Non-Inverting, Single Input negative voltage (V) -5 Rating Catalog Undervoltage lockout (typ) (V) 8 Driver configuration Non-Inverting, Single
SOT-23 (DBV) 6 8.12 mm² 2.9 x 2.8
  • Low Cost Gate Driver (offering optimal solution for driving
    FET and IGBTs)
  • Superior Replacement to Discrete Transistor Pair Drive (providing
    easy interface with controller)
  • CMOS Compatible Input Logic Threshold (becomes fixed at VDD above 18 V)
  • Split Outputs Allow Separate Turn-On and Turn-Off Tuning
  • Enable with Fixed TTL Compatible Threshold
  • High 2.5-A Source and 5-A Sink Peak Drive Currents at 18-V VDD
  • Wide VDD Range From 10 V up to 35 V
  • Input Pins Capable of Withstanding up to -5-V DC Below Ground
  • Output Held Low When Inputs are Floating or During VDD UVLO
  • Fast Propagation Delays (17-ns typical)
  • Fast Rise and Fall Times
    (15-ns and 7-ns typical with 1800-pF Load)
  • Under Voltage Lockout (UVLO)
  • Used as a High-Side or Low-Side Driver (if designed with
    proper bias and signal isolation)
  • Low Cost, Space Saving 6-Pin DBV (SOT-23) Package
  • Operating Temperature Range of –40°C to 140°C
  • Low Cost Gate Driver (offering optimal solution for driving
    FET and IGBTs)
  • Superior Replacement to Discrete Transistor Pair Drive (providing
    easy interface with controller)
  • CMOS Compatible Input Logic Threshold (becomes fixed at VDD above 18 V)
  • Split Outputs Allow Separate Turn-On and Turn-Off Tuning
  • Enable with Fixed TTL Compatible Threshold
  • High 2.5-A Source and 5-A Sink Peak Drive Currents at 18-V VDD
  • Wide VDD Range From 10 V up to 35 V
  • Input Pins Capable of Withstanding up to -5-V DC Below Ground
  • Output Held Low When Inputs are Floating or During VDD UVLO
  • Fast Propagation Delays (17-ns typical)
  • Fast Rise and Fall Times
    (15-ns and 7-ns typical with 1800-pF Load)
  • Under Voltage Lockout (UVLO)
  • Used as a High-Side or Low-Side Driver (if designed with
    proper bias and signal isolation)
  • Low Cost, Space Saving 6-Pin DBV (SOT-23) Package
  • Operating Temperature Range of –40°C to 140°C

The UCC27532 is a single-channel, high-speed, gate driver capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn-on effect. The UCC27532 device also features a split-output configuration where the gate-drive current is sourced through OUTH pin and sunk through OUTL pin. This pin arrangement allows the user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the switching slew rates.

The driver has rail-to-rail drive capability and extremely small propagation delay typically 17 ns.

The UCC27532DBV has CMOS input threshold centered 55% rise and 45% fall in regards of VDD at VDD below or equal 18 V. When VDD is above 18 V, the input threshold remains fixed at its maximum level.

The driver has EN pin with fixed TTL compatible threshold. EN is internally pulled up; pulling EN low disables driver, while leaving it open provides normal operation. The EN pin can be used as an additional input with the same performance as the IN pin.

Leaving the input pin of driver open holds the output low. The logic behavior of the driver is shown in the application diagram, timing diagram and input and output logic truth table.

Internal circuitry on VDD pin provides an under voltage lockout function that holds output low until VDD supply voltage is within operating range.

The UCC27532 driver is offered in a 6-pin standard SOT-23 (DBV) package. The device operates over wide temperature range of –40°C to 140°C.

The UCC27532 is a single-channel, high-speed, gate driver capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn-on effect. The UCC27532 device also features a split-output configuration where the gate-drive current is sourced through OUTH pin and sunk through OUTL pin. This pin arrangement allows the user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the switching slew rates.

The driver has rail-to-rail drive capability and extremely small propagation delay typically 17 ns.

The UCC27532DBV has CMOS input threshold centered 55% rise and 45% fall in regards of VDD at VDD below or equal 18 V. When VDD is above 18 V, the input threshold remains fixed at its maximum level.

The driver has EN pin with fixed TTL compatible threshold. EN is internally pulled up; pulling EN low disables driver, while leaving it open provides normal operation. The EN pin can be used as an additional input with the same performance as the IN pin.

Leaving the input pin of driver open holds the output low. The logic behavior of the driver is shown in the application diagram, timing diagram and input and output logic truth table.

Internal circuitry on VDD pin provides an under voltage lockout function that holds output low until VDD supply voltage is within operating range.

The UCC27532 driver is offered in a 6-pin standard SOT-23 (DBV) package. The device operates over wide temperature range of –40°C to 140°C.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
11 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート FET および IGBT シングル・ゲート・ドライバ シンクピーク電流: 5A およびソースピーク電流: 2.5A、35VMAX VDD データシート 2013年 2月 5日
アプリケーション・ノート Using a Single-Output Gate-Driver for High-Side or Low-Side Drive (Rev. B) PDF | HTML 2023年 9月 8日
アプリケーション概要 External Gate Resistor Selection Guide (Rev. A) 2020年 2月 28日
アプリケーション概要 Understanding Peak IOH and IOL Currents (Rev. A) 2020年 2月 28日
アプリケーション概要 Implementing a Bipolar Gate Drive for Low-Side IGBTs and SiC FETs in Motor Drive 2019年 10月 10日
その他の技術資料 Fundamentals of MOSFET and IGBT Gate Driver Circuits (Replaces SLUP169) (Rev. A) 2018年 10月 29日
セレクション・ガイド 電源 IC セレクション・ガイド 2018 (Rev. R 翻訳版) 英語版 (Rev.R) 2018年 9月 13日
アプリケーション・ノート UCC27531 35-V Gate Driver for SiC MOSFET Applications (Rev. A) 2018年 5月 8日
アプリケーション概要 Low-Side Gate Drivers With UVLO Versus BJT Totem-Pole 2018年 3月 16日
その他の技術資料 FETおよびIGBTシングル・ゲート・ドライバ シンクピーク電流:5Aおよびソースピーク電流: 2.5A、35VMAX VDD 2014年 4月 3日
EVM ユーザー ガイド (英語) Using the UCC27532EVM-538 (Rev. A) 2013年 8月 22日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

UCC27531EVM-184 — UCC27531 評価モジュール

The UCC27531EVM-184 is a fully isolated Gate Driver Daughter Card that provides a test platform for a quick and easy evaluation of the UCC27531DBV driver. Powered by a single +12V external supply, and featuring a comprehensive set of test points and jumpers, this EVM can be used for the evaluation (...)
ユーザー ガイド: PDF
シミュレーション・モデル

UCC27532 PSpice Transient Model (Rev. A)

SLUM355A.ZIP (37 KB) - PSpice Model
シミュレーション・モデル

UCC27532 Unencrypted PSpice Transient Model

SLVMBG9.ZIP (2 KB) - PSpice Model
計算ツール

SLURB21 UCC2753X Schematic Review Template

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
ローサイド・ドライバ
UCC27531 8V UVLO、35V VDD 対応、分割出力対応、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27531-Q1 車載、8V UVLO、35V VDD、分割出力対応、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27532 8V UVLO、35V VDD 対応、複数の CMOS 入力、分割出力対応、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27532-Q1 車載、8V UVLO、35V VDD、CMOS 入力、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27533 8V UVLO、35V VDD 対応、反転入力と非反転入力、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27536 8V UVLO、35V VDD 対応、反転入力、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27537 8V UVLO、35V VDD 対応、EN (イネーブル) ピン採用、2.5A/5A、シングルチャネル・ゲート・ドライバ UCC27538 8V UVLO、35V VDD 対応、デュアル入力、2.5A/5A、シングルチャネル・ゲート・ドライバ
シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
リファレンス・デザイン

PMP11303 — 高効率 350W AC/DC 電源、リファレンス・デザイン

PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no (...)
試験報告書: PDF
回路図: PDF
リファレンス・デザイン

PMP30192 — コンボ IC を使用するユニバーサル入力、360W PFC + LLC のリファレンス・デザイン

This power supply reference design consists of a synchronous-rectification LLC isolated half-bridge associated to a CCM PFC stage. It needs 14V-primary (100mA max.) and 7V-secondary (50mA max.) as bias supply. Thanks to low-profile construction (20mm height), it can be employed in LCD screen (...)
試験報告書: PDF
回路図: PDF
パッケージ ピン数 ダウンロード
SOT-23 (DBV) 6 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ