ホーム パワー・マネージメント デジタル電源 IC デジタル電源制御ドライバとパワートレイン・モジュール

UCD74106

アクティブ

デジタル、同期整流・降圧、パワー・ドライバ

製品詳細

Supply voltage (min) (V) 2.2 Supply voltage (max) (V) 18 Number of outputs 1 Peak output current (A) 6 Input threshold CMOS Propagation delay time (µs) 0.02 Driver configuration Single Operating temperature range (°C) -40 to 125 Rating Catalog
Supply voltage (min) (V) 2.2 Supply voltage (max) (V) 18 Number of outputs 1 Peak output current (A) 6 Input threshold CMOS Propagation delay time (µs) 0.02 Driver configuration Single Operating temperature range (°C) -40 to 125 Rating Catalog
VQFN-HR (RGM) 13 9 mm² 3 x 3
  • Fully Integrated Power Switches With Drivers for Single and Multiphase Synchronous Buck Converters
  • Full Compatibility With TI Fusion Digital Power Supply Controllers, (UCD91xx and UCD92xx Families)
  • Compatible With Analog Domain Controllers
  • Wide Input Voltage Range:
    • 4.5 V to 14 V
    • Operational Down to 2.2-V Input With an External Bias Supply
  • Up to 6-A Output Current
  • Operational to 2-MHz Switching Frequency
  • Current Limit With Current Limit Flag
  • Onboard Regulated 6-V Driver Supply From VIN
  • Thermal Protection and Monitoring
  • Fully Integrated Power Switches With Drivers for Single and Multiphase Synchronous Buck Converters
  • Full Compatibility With TI Fusion Digital Power Supply Controllers, (UCD91xx and UCD92xx Families)
  • Compatible With Analog Domain Controllers
  • Wide Input Voltage Range:
    • 4.5 V to 14 V
    • Operational Down to 2.2-V Input With an External Bias Supply
  • Up to 6-A Output Current
  • Operational to 2-MHz Switching Frequency
  • Current Limit With Current Limit Flag
  • Onboard Regulated 6-V Driver Supply From VIN
  • Thermal Protection and Monitoring

The UCD74106 is a complete power system ready to drive a buck power supply (). High-side MOSFETs, low-side MOSFETs, drivers, current sensing circuitry and necessary protection functions are all integrated into one monolithic solution to facilitate minimum size and maximum efficiency. Driver circuits provide high charge and discharge current for the high-side NMOS switch and the low-side NMOS synchronous rectifier in a synchronous buck circuit. The MOSFET gates are driven to 6.25 V by an internally regulated VGG supply. The internal VGG regulator can be disabled to permit the user to supply an independent gate drive voltage. This flexibility allows a wide power conversion input voltage range of 2.2 V to 18 V. Internal Under Voltage Lockout (UVLO) logic insures VGG is good before allowing chip operation.

A drive logic block allows operation in one of two modes. In synchronous mode, the logic block uses the PWM signal to control both the high-side and low-side gate drive signals. Dead time is optimized to prevent cross conduction. The synchronous rectifier enable (SRE) pin controls whether or not the low-side FET is turned on when the PWM signal is low.

The UCD74106 is a complete power system ready to drive a buck power supply (). High-side MOSFETs, low-side MOSFETs, drivers, current sensing circuitry and necessary protection functions are all integrated into one monolithic solution to facilitate minimum size and maximum efficiency. Driver circuits provide high charge and discharge current for the high-side NMOS switch and the low-side NMOS synchronous rectifier in a synchronous buck circuit. The MOSFET gates are driven to 6.25 V by an internally regulated VGG supply. The internal VGG regulator can be disabled to permit the user to supply an independent gate drive voltage. This flexibility allows a wide power conversion input voltage range of 2.2 V to 18 V. Internal Under Voltage Lockout (UVLO) logic insures VGG is good before allowing chip operation.

A drive logic block allows operation in one of two modes. In synchronous mode, the logic block uses the PWM signal to control both the high-side and low-side gate drive signals. Dead time is optimized to prevent cross conduction. The synchronous rectifier enable (SRE) pin controls whether or not the low-side FET is turned on when the PWM signal is low.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
2 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート Synchronous-Buck Power Stage データシート (Rev. A) 2012年 12月 19日
セレクション・ガイド 電源 IC セレクション・ガイド 2018 (Rev. R 翻訳版) 英語版 (Rev.R) 2018年 9月 13日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

アプリケーション・ソフトウェアとフレームワーク

FUSION_DIGITAL_POWER_DESIGNER — デジタル電源用ソフトウェア

Fusion Digital Power™ は、TI のデジタル電源コントローラとシーケンサ / ヘルス・モニタの構成および監視を行うためのグラフィカル・ユーザー・インターフェイス (GUI) ソフトウェアです。アプリケーションは PMBus プロトコルを使用し、TI の USB アダプタとシリアル・バス経由でデバイスとの通信を行います。
アプリケーション・ソフトウェアとフレームワーク

FUSION_MFR_GUI — Fusion Digital Power 作成ツール

The Fusion Digital Power Manufacturing Tool (aka MFR GUI) is a Graphical User Interface used to download firmware, upgrade firmware, configure, calibrate and test .

The MFR GUI supports the same devices as Fusion Digital Power Designer software.  This tool is typically used in manufacturing (...)

シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
パッケージ ピン数 ダウンロード
VQFN-HR (RGM) 13 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ