TAS5424C-Q1

最終購入段階

車載、I2C 診断機能とロード・ダンプ対応機能搭載、PBTL、28W、4 チャネル、6 ~ 24V、アナログ入力 Class-D オーディオ・アンプ

TAS5424C-Q1 は生産中止予定です
以下の代替品のいずれかをご検討ください。
open-in-new 代替品と比較
比較対象デバイスと同等の機能で、ピン配置が異なる製品
TAS5414C-Q1 アクティブ 車載、I2C 診断機能とロード・ダンプ対応機能搭載、PBTL、28W、4 チャネル、6 ~ 24V、アナログ SE (シングルエンド) 入力 Class-D オーディオ・アンプ TAS5414C-Q1 comes in 64 pin PHD package, while TAS5424C-Q1 comes in smaller 44 pin DKE package
比較対象デバイスと類似の機能
TAS6424E-Q1 アクティブ 車載、75W、2MHz、クワッドチャネル、4.5 ~ 26.4V、デジタル入力 Class-D オーディオ・アンプ Replacement

製品詳細

Audio input type Analog Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 24 Power stage supply (min) (V) 6 Load (min) (Ω) 2 Output power (W) 45 THD + N at 1 kHz (%) 0.02 Iq (typ) (mA) 60 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 6 Analog supply voltage (max) (V) 24 PSRR (dB) 70 Operating temperature range (°C) -40 to 105
Audio input type Analog Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 24 Power stage supply (min) (V) 6 Load (min) (Ω) 2 Output power (W) 45 THD + N at 1 kHz (%) 0.02 Iq (typ) (mA) 60 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 6 Analog supply voltage (max) (V) 24 PSRR (dB) 70 Operating temperature range (°C) -40 to 105
HSSOP (DKE) 44 225.78 mm² 15.9 x 14.2
  • AEC-Q100 Qualified for Automotive Applications
    • Device Temperature: –55°C to 125°C Ambient
    • Device HBM Classification Level: ±2500 V
    • Device CDM Classification Level: ±500 V
  • TAS5414C-Q1 – Single-Ended Input
  • TAS5424C-Q1 – Differential Input
  • Four-Channel Digital Power Amplifier
  • Four Analog Inputs, Four BTL Power Outputs
  • Typical Output Power at 10% THD+N
    • 28 W/Ch Into 4 Ω at 14.4 V
    • 50 W/Ch Into 2 Ω at 14.4 V
    • 79 W/Ch Into 4 Ω at 24 V
    • 150 W/Ch Into 2 Ω at 24 V (PBTL)
  • Channels Can Be Paralleled (PBTL) for High-Current Applications
  • THD+N < 0.02%, 1 kHz, 1 W Into 4 Ω
  • Patented Pop- and Click-Reduction Technology
    • Soft Muting With Gain Ramp Control
    • Common-Mode Ramping
  • Patented AM Interference Avoidance
  • Patented Cycle-by-Cycle Current Limit
  • 75-dB PSRR
  • Four-Address I2C Serial Interface for Device Configuration and Control
  • Channel Gains: 12-dB, 20-dB, 26-dB, 32-dB
  • Load Diagnostic Functions:
    • Output Open and Shorted Load
    • Output-to-Power and -to-Ground Shorts
    • Patented Tweeter Detection
  • Protection and Monitoring Functions:
    • Short-Circuit Protection
    • Load-Dump Protection to 50 V
    • Fortuitous Open-Ground and -Power Tolerant
    • Patented Output DC Level Detection While Music Playing
    • Overtemperature Protection
    • Over- and Undervoltage Conditions
    • Clip Detection
  • 44-Pin PSOP3 (DKE) Power SOP Package With Heat Slug Up for TAS5424C-Q1
  • 64-Pin QFP (PHD) Power Package With Heat Slug Up for TAS5414C-Q1
  • Designed for Automotive EMC Requirements
  • ISO9000:2002 TS16949 Certified
  • –40°C to 105°C Ambient Temperature Range
  • AEC-Q100 Qualified for Automotive Applications
    • Device Temperature: –55°C to 125°C Ambient
    • Device HBM Classification Level: ±2500 V
    • Device CDM Classification Level: ±500 V
  • TAS5414C-Q1 – Single-Ended Input
  • TAS5424C-Q1 – Differential Input
  • Four-Channel Digital Power Amplifier
  • Four Analog Inputs, Four BTL Power Outputs
  • Typical Output Power at 10% THD+N
    • 28 W/Ch Into 4 Ω at 14.4 V
    • 50 W/Ch Into 2 Ω at 14.4 V
    • 79 W/Ch Into 4 Ω at 24 V
    • 150 W/Ch Into 2 Ω at 24 V (PBTL)
  • Channels Can Be Paralleled (PBTL) for High-Current Applications
  • THD+N < 0.02%, 1 kHz, 1 W Into 4 Ω
  • Patented Pop- and Click-Reduction Technology
    • Soft Muting With Gain Ramp Control
    • Common-Mode Ramping
  • Patented AM Interference Avoidance
  • Patented Cycle-by-Cycle Current Limit
  • 75-dB PSRR
  • Four-Address I2C Serial Interface for Device Configuration and Control
  • Channel Gains: 12-dB, 20-dB, 26-dB, 32-dB
  • Load Diagnostic Functions:
    • Output Open and Shorted Load
    • Output-to-Power and -to-Ground Shorts
    • Patented Tweeter Detection
  • Protection and Monitoring Functions:
    • Short-Circuit Protection
    • Load-Dump Protection to 50 V
    • Fortuitous Open-Ground and -Power Tolerant
    • Patented Output DC Level Detection While Music Playing
    • Overtemperature Protection
    • Over- and Undervoltage Conditions
    • Clip Detection
  • 44-Pin PSOP3 (DKE) Power SOP Package With Heat Slug Up for TAS5424C-Q1
  • 64-Pin QFP (PHD) Power Package With Heat Slug Up for TAS5414C-Q1
  • Designed for Automotive EMC Requirements
  • ISO9000:2002 TS16949 Certified
  • –40°C to 105°C Ambient Temperature Range

The TAS5414C-Q1 and TAS5424C-Q1 are four-channel digital audio amplifiers designed for use in automotive head units and external amplifier modules. They provide four channels at 23 W continuously into 4 Ω at less than 1% THD+N from a 14.4-V supply. Each channel can also deliver 38 W into 2 Ω at 1% THD+N. The TAS5414C-Q1 uses single-ended analog inputs, whereas the TAS5424C-Q1 employs differential inputs for increased immunity to common-mode system noise. The digital PWM topology of the device provides dramatic improvements in efficiency over traditional linear amplifier solutions. This reduces the power dissipated by the amplifier by a factor of ten under typical music playback conditions. The device incorporates all the functionality needed to perform in the demanding OEM applications area. The devices have built-in load diagnostic functions for detecting and diagnosing misconnected outputs to help to reduce test time during the manufacturing process.

The TAS5414C-Q1 and TAS5424C-Q1 are four-channel digital audio amplifiers designed for use in automotive head units and external amplifier modules. They provide four channels at 23 W continuously into 4 Ω at less than 1% THD+N from a 14.4-V supply. Each channel can also deliver 38 W into 2 Ω at 1% THD+N. The TAS5414C-Q1 uses single-ended analog inputs, whereas the TAS5424C-Q1 employs differential inputs for increased immunity to common-mode system noise. The digital PWM topology of the device provides dramatic improvements in efficiency over traditional linear amplifier solutions. This reduces the power dissipated by the amplifier by a factor of ten under typical music playback conditions. The device incorporates all the functionality needed to perform in the demanding OEM applications area. The devices have built-in load diagnostic functions for detecting and diagnosing misconnected outputs to help to reduce test time during the manufacturing process.

ダウンロード 字幕付きのビデオを表示 ビデオ

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
6 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート TAS54x4C-Q1 Four-Channel Automotive Digital Amplifiers データシート (Rev. F) PDF | HTML 2017年 10月 24日
アプリケーション・ノート Guidelines for Measuring Audio Power Amplifier Performance (Rev. A) 2019年 8月 26日
アプリケーション・ノート AN-1849 An Audio Amplifier Power Supply Design (Rev. C) 2019年 6月 27日
設計ガイド TAS54x4C Design Guide 2014年 6月 18日
アプリケーション・ノート AN-1737 Managing EMI in Class D Audio Applications (Rev. A) 2013年 5月 1日
EVM ユーザー ガイド (英語) TAS5414C EVM User Guide 2013年 1月 18日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

評価ボード

TAS5424CQ1DKEEVM — TAS5424CQ1DKEEVM - 4 チャネル・オートモーティブ・デジタル・アンプ評価モジュール

The TAS5424CQ1DKEEVM is a four channel automotive Class D amplifier evaluation module, utilizing the TAS5424C-Q1. The EVM consists of a single printed circuit board (PCB) mounted inside a metal chassis for EMC testing. The EVM must have an external I2C controller board to function. The USB-to-I2C (...)

ユーザー ガイド: PDF
評価基板 (EVM) 向けの GUI

SLOC287 TAS54x4C EVM GUI

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
スピーカ・アンプ
TAS5414C-Q1 車載、I2C 診断機能とロード・ダンプ対応機能搭載、PBTL、28W、4 チャネル、6 ~ 24V、アナログ SE (シングルエンド) 入力 Class-D オーディオ・アンプ TAS5424C-Q1 車載、I2C 診断機能とロード・ダンプ対応機能搭載、PBTL、28W、4 チャネル、6 ~ 24V、アナログ入力 Class-D オーディオ・アンプ
ハードウェア開発
評価ボード
TAS5414CQ1PHDEVM TAS5414C-Q1 PHD 評価モジュール TAS5424CQ1DKEEVM TAS5424CQ1DKEEVM - 4 チャネル・オートモーティブ・デジタル・アンプ評価モジュール
シミュレーション・モデル

TAS5424C IBIS Model

SLOM479.ZIP (49 KB) - IBIS Model
アセンブリの図面

TAS5424C-Q1 Gerber, Schematic, Layout and BOM

SLOR119.ZIP (2591 KB)
シミュレーション・ツール

PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®

PSpice® for TI は、各種アナログ回路の機能評価に役立つ、設計とシミュレーション向けの環境です。設計とシミュレーションに適したこのフル機能スイートは、Cadence® のアナログ分析エンジンを使用しています。PSpice for TI は無償で使用でき、アナログや電源に関する TI の製品ラインアップを対象とする、業界でも有数の大規模なモデル・ライブラリが付属しているほか、選択された一部のアナログ動作モデルも利用できます。

設計とシミュレーション向けの環境である PSpice for TI (...)
パッケージ ピン数 ダウンロード
HSSOP (DKE) 44 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ