JAJSGG2C October   2018  – June 2019 ADS125H02

PRODUCTION DATA.  

  1. 特長
  2. アプリケーション
  3. 概要
    1.     機能ブロック図
  4. 改訂履歴
  5. 概要(続き)
  6. Device Comparison Table
  7. Pin Configuration and Functions
    1.     Pin Functions
  8. Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Switching Characteristics
    8. 8.8 Typical Characteristics
  9. Parameter Measurement Information
    1. 9.1 Noise Performance
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1 Input Range
      2. 10.3.2 Analog Inputs
        1. 10.3.2.1 ESD Diodes
        2. 10.3.2.2 Input Multiplexer
          1. 10.3.2.2.1 Analog Inputs (AIN0, AIN1, AINCOM)
          2. 10.3.2.2.2 High-Voltage Power Supply Readback
          3. 10.3.2.2.3 Internal VCOM Connection (Default)
          4. 10.3.2.2.4 Temperature Sensor
      3. 10.3.3 Programmable Gain Amplifier (PGA)
        1. 10.3.3.1 PGA Operating Range
        2. 10.3.3.2 PGA Monitor
      4. 10.3.4 Reference Voltage
        1. 10.3.4.1 Internal Reference
        2. 10.3.4.2 External Reference
        3. 10.3.4.3 AVDD Power-Supply Reference
        4. 10.3.4.4 Reference Monitor
      5. 10.3.5 Current Sources (IDAC1 and IDAC2)
      6. 10.3.6 General-Purpose Inputs and Outputs (GPIOs)
      7. 10.3.7 ADC Modulator
      8. 10.3.8 Digital Filter
        1. 10.3.8.1 Sinc Filter Mode
          1. 10.3.8.1.1 Sinc Filter Frequency Response
        2. 10.3.8.2 FIR Filter
        3. 10.3.8.3 50-Hz and 60-Hz Normal Mode Rejection
    4. 10.4 Device Functional Modes
      1. 10.4.1 Conversion Control
        1. 10.4.1.1 Continuous-Conversion Mode
        2. 10.4.1.2 Pulse-Conversion Mode
        3. 10.4.1.3 Conversion Latency
        4. 10.4.1.4 Start-Conversion Delay
      2. 10.4.2 Auto-Zero Mode
      3. 10.4.3 Clock Mode
      4. 10.4.4 Reset
        1. 10.4.4.1 Power-On Reset
        2. 10.4.4.2 Reset by Pin
        3. 10.4.4.3 Reset by Command
      5. 10.4.5 Calibration
        1. 10.4.5.1 Offset and Full-Scale Calibration
          1. 10.4.5.1.1 Offset Calibration Registers
          2. 10.4.5.1.2 Full-Scale Calibration Registers
        2. 10.4.5.2 Offset Calibration (OFSCAL)
        3. 10.4.5.3 Full-Scale Calibration (GANCAL)
        4. 10.4.5.4 Calibration Command Procedure
        5. 10.4.5.5 User Calibration Procedure
    5. 10.5 Programming
      1. 10.5.1 Serial Interface
        1. 10.5.1.1 Chip-Select Pins (CS1 and CS2)
        2. 10.5.1.2 Serial Clock (SCLK)
        3. 10.5.1.3 Data Input (DIN)
        4. 10.5.1.4 Data Output/Data Ready (DOUT/DRDY)
      2. 10.5.2 Data Ready (DRDY)
        1. 10.5.2.1 DRDY in Continuous-Conversion Mode
        2. 10.5.2.2 DRDY in Pulse-Conversion Mode
        3. 10.5.2.3 Data Ready by Software Polling
      3. 10.5.3 Conversion Data
        1. 10.5.3.1 Status Byte (STATUS0)
        2. 10.5.3.2 Conversion Data Format
      4. 10.5.4 Cyclic Redundancy Check (CRC)
      5. 10.5.5 Commands
        1. 10.5.5.1  General Command Format
        2. 10.5.5.2  NOP Command
        3. 10.5.5.3  RESET Command
        4. 10.5.5.4  START Command
        5. 10.5.5.5  STOP Command
        6. 10.5.5.6  RDATA Command
        7. 10.5.5.7  OFSCAL Command
        8. 10.5.5.8  GANCAL Command
        9. 10.5.5.9  RREG Command
        10. 10.5.5.10 WREG Command
        11. 10.5.5.11 LOCK Command
        12. 10.5.5.12 UNLOCK Command
    6. 10.6 Register Map
      1. 10.6.1  Device Identification (ID) Register (address = 00h) [reset = 6xh]
        1. Table 30. ID Register Field Descriptions
      2. 10.6.2  Main Status (STATUS0) Register (address = 01h) [reset = 01h]
        1. Table 31. STATUS0 Register Field Descriptions
      3. 10.6.3  Mode 0 (MODE0) Register (address = 02h) [reset = 24h]
        1. Table 32. MODE0 Register Field Descriptions
      4. 10.6.4  Mode 1 (MODE1) Register (address = 03h) [reset = 01h]
        1. Table 33. MODE1 Register Field Descriptions
      5. 10.6.5  Mode 2 (MODE2) Register (address = 04h) [reset = 00h]
        1. Table 34. MODE2 Register Field Descriptions
      6. 10.6.6  Mode 3 (MODE3) Register (address = 05h) [reset = 00h]
        1. Table 35. MODE3 Register Field Descriptions
      7. 10.6.7  Reference Configuration (REF) Register (address = 06h) [reset = 05h]
        1. Table 36. REF Register Field Descriptions
      8. 10.6.8  Offset Calibration (OFCALx) Registers (address = 07h, 08h, 09h) [reset = 00h, 00h, 00h]
        1. Table 37. OFCAL0, OFCAL1, OFCAL2 Registers Field Description
      9. 10.6.9  Full-Scale Calibration (FSCALx) Registers (address = 0Ah, 0Bh, 0Ch) [reset = 00h, 00h, 40h]
        1. Table 38. FSCAL0, FSCAL1, FSCAL2 Registers Field Description
      10. 10.6.10 Current Source Multiplexer (I_MUX) Register (address = 0Dh) [reset = FFh]
        1. Table 39. I_MUX Register Field Descriptions
      11. 10.6.11 Current Source Magnitude (I_MAG) Register (address = 0Eh) [reset = 00h]
        1. Table 40. I_MAG Register Field Descriptions
      12. 10.6.12 Reserved (RESERVED) Register (address = 0Fh) [reset = 00h]
        1. Table 41. RESERVED Register Field Descriptions
      13. 10.6.13 MODE4 (MODE4) Register (address = 10h) [reset = 50h]
        1. Table 42. MODE4 Register Field Descriptions
      14. 10.6.14 PGA Alarm (STATUS1) Register (address = 11h) [reset = xxh]
        1. Table 43. STATUS1 Register Field Descriptions
      15. 10.6.15 Status 2 (STATUS2) Register (address = 12h) [reset = 0xh]
        1. Table 44. STATUS2 Register Field Descriptions
  11. 11Application and Implementation
    1. 11.1 Application Information
      1. 11.1.1 Input Range
      2. 11.1.2 Input Overload
        1. 11.1.2.1 Input Signal Rate of Change (dV/dt)
      3. 11.1.3 Unused Inputs and Outputs
    2. 11.2 Typical Applications
      1. 11.2.1 ±10-V Analog Input Module
        1. 11.2.1.1 Design Requirements
        2. 11.2.1.2 Detailed Design Procedure
        3. 11.2.1.3 Application Curves
      2. 11.2.2 Thermocouple Input With High Common-Mode Voltage
    3. 11.3 Initialization Setup
  12. 12Power Supply Recommendations
    1. 12.1 Power-Supply Decoupling
    2. 12.2 Analog Power-Supply Clamp
    3. 12.3 Power-Supply Sequencing
    4. 12.4 5-V to ±15-V DC-DC Converter
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
  14. 14デバイスおよびドキュメントのサポート
    1. 14.1 ドキュメントのサポート
      1. 14.1.1 関連資料
    2. 14.2 ドキュメントの更新通知を受け取る方法
    3. 14.3 コミュニティ・リソース
    4. 14.4 商標
    5. 14.5 静電気放電に関する注意事項
    6. 14.6 Glossary
  15. 15メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Main Status (STATUS0) Register (address = 01h) [reset = 01h]

STATUS0 is shown in Figure 83 and described in Table 31.

Return to Register Map Summary.

Figure 83. STATUS0 Register
7 6 5 4 3 2 1 0
LOCK1 CRC1 0 STAT12 REFALM DRDY CLOCK RESET
R-0h R/W-0h R-0h R-0h R-0h R-0h R-xh R/W-1h

Table 31. STATUS0 Register Field Descriptions

Bit Field Type Reset Description
7 LOCK1 R 0h

Register Write Lock1 Status

Indicates the register write lock status of register addresses 00h to 0Fh. See the LOCK Command section for details.

0: Registers 00h to 0Fh are not locked (default)

1: Registers 00h to 0Fh are locked

See the STATUS2 register for the register lock status of register addresses 10h to 12h.

6 CRC1 R/W 0h

CRC1 Error

Indicates if a CRC error occurred during commands when CS1 is active. Write 0 to clear the CRC error.

0: No CRC error during commands using CS1

1: CRC error occurred during commands using CS1

See the STATUS2 register for the CRC error status for commands using CS2.

5 0 R 0h

Reserved

Always write 0.

4 STAT12 R 0h

STAT12 Error Flag

Indicates one or more error events have been logged in the STATUS1 or STATUS2 registers. Read the STATUS1 and STATUS2 registers to determine the error. This bit clears after all errors are cleared.

0: No error

1: Error logged to the STATUS1 or STATUS2 registers

3 REFALM R 0h

Reference Voltage Alarm

This bit sets when the reference voltage falls below < 0.4 V (typical). The alarm updates at each new conversion cycle (auto-reset).

0: No reference low alarm

1: Reference low alarm

2 DRDY R 0h

Data Ready

Indicates new conversion data.

0: Conversion data are not new since the last data read

1: Conversion data are new since the last data read

1 CLOCK R xh

Clock

Indicates internal or external clock mode. The ADC automatically selects the clock mode.

0: ADC clock is internal

1: ADC clock is external

0 RESET R/W 1h

Reset

Indicates an ADC reset has occurred. Clear the bit to detect the next device reset.

0: No reset

1: Reset (default)