JAJSCW7D January   2016  – November 2018 DRV8884

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      概略回路図
      2.      マイクロステッピング電流の波形
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Indexer Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Stepper Motor Driver Current Ratings
        1. 8.3.1.1 Peak Current Rating
        2. 8.3.1.2 RMS Current Rating
        3. 8.3.1.3 Full-Scale Current Rating
      2. 8.3.2  PWM Motor Drivers
      3. 8.3.3  Microstepping Indexer
      4. 8.3.4  Current Regulation
      5. 8.3.5  Controlling RREF With an MCU DAC
      6. 8.3.6  Decay Modes
        1. 8.3.6.1 Mode 1: Slow Decay for Increasing and Decreasing Current
        2. 8.3.6.2 Mode 2: Slow Decay for Increasing Current, Mixed Decay for Decreasing Current
        3. 8.3.6.3 Mode 3: Mixed Decay for Increasing and Decreasing Current
      7. 8.3.7  Blanking Time
      8. 8.3.8  Charge Pump
      9. 8.3.9  LDO Voltage Regulator
      10. 8.3.10 Logic and Multi-Level Pin Diagrams
      11. 8.3.11 Protection Circuits
        1. 8.3.11.1 VM UVLO
        2. 8.3.11.2 VCP Undervoltage Lockout (CPUV)
        3. 8.3.11.3 Overcurrent Protection (OCP)
        4. 8.3.11.4 Thermal Shutdown (TSD)
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Stepper Motor Speed
        2. 9.2.2.2 Current Regulation
        3. 9.2.2.3 Decay Modes
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 ドキュメントのサポート
      1. 12.1.1 関連資料
    2. 12.2 ドキュメントの更新通知を受け取る方法
    3. 12.3 コミュニティ・リソース
    4. 12.4 商標
    5. 12.5 静電気放電に関する注意事項
    6. 12.6 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.3 Feature Description

Table 1 lists the recommended external components for the DRV8884 device.

Table 1. External Components

COMPONENT PIN 1 PIN 2 RECOMMENDED
CVM VM GND Two 0.01-µF ceramic capacitors rated for VM
CVM VM GND Bulk electrolytic capacitor rated for VM
CVCP VCP VM 16-V, 0.22-µF ceramic capacitor
CSW CPH CPL 0.022-µF X7R capacitor rated for VM
CAVDD AVDD GND 6.3-V, 0.47-µF ceramic capacitor
CDVDD DVDD GND 6.3-V, 0.47-µF ceramic capacitor
RnFAULT VCC (1) nFAULT >4.7 kΩ
RREF RREF GND Resistor to limit chopping current must be installed. See the Typical Application section for value selection.
(1) VCC is not a pin on the DRV8884, but a VCC supply voltage pullup is required for open-drain output nFAULT; nFAULT may be pulled up to DVDD