JAJSL98B October   2020  – June 2021 LMG3522R030-Q1 , LMG3525R030-Q1

ADVANCE INFORMATION  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
  8. 8 Parameter Measurement Information
    1. 8.1 Switching Parameters
      1. 8.1.1 Turn-On Delays
      2. 8.1.2 Turn-Off Delays
      3. 8.1.3 Drain Slew Rate
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Direct-Drive GaN Architecture
      2. 9.3.2 Drain-Source Voltage Capability
      3. 9.3.3 Internal Buck-Boost DC-DC Converter
      4. 9.3.4 VDD Bias Supply
      5. 9.3.5 Auxiliary LDO
      6. 9.3.6 Fault Detection
        1. 9.3.6.1 Overcurrent Protection and Short-Circuit Protection
        2. 9.3.6.2 Overtemperature Shutdown
        3. 9.3.6.3 UVLO Protection
        4. 9.3.6.4 Fault Reporting
      7. 9.3.7 Drive Strength Adjustment
      8. 9.3.8 Temperature-Sensing Output
      9. 9.3.9 Sync-FET Mode Operation
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Slew Rate Selection
          1. 10.2.2.1.1 Start-Up and Slew Rate With Bootstrap High-Side Supply
        2. 10.2.2.2 Signal Level-Shifting
        3. 10.2.2.3 Buck-Boost Converter Design
    3. 10.3 Do's and Don'ts
  11. 11Power Supply Recommendations
    1. 11.1 Using an Isolated Power Supply
    2. 11.2 Using a Bootstrap Diode
      1. 11.2.1 Diode Selection
      2. 11.2.2 Managing the Bootstrap Voltage
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Power Loop Inductance
      2. 12.1.2 Signal Ground Connection
      3. 12.1.3 Bypass Capacitors
      4. 12.1.4 Switch-Node Capacitance
      5. 12.1.5 Signal Integrity
      6. 12.1.6 High-Voltage Spacing
      7. 12.1.7 Thermal Recommendations
    2. 12.2 Layout Examples
  13. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 サポート・リソース
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Export Control Notice
    7. 13.7 Glossary
  14. 14Mechanical, Packaging, and Orderable Information
    1. 14.1 Tape and Reel Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • RQS|52
サーマルパッド・メカニカル・データ
発注情報

7.3 Recommended Operating Conditions

Unless otherwise noted: voltages are respect to SOURCE connected to reference ground.
MIN NOM MAX UNIT
VDS Drain-source voltage (FET Switching) 520 V
VDS(tr) Drain-source transient ringing peak voltage (FET Off)(1) 650 V
VDS dv/dt Drain-source edge rate immunity for FET to remain off (half-bridge configuration)(2) 200 V/ns
Supply voltage VDD
(Maximum switching frequency derated for VVDD < 9 V)		 7.5 12 18 V
Input voltage IN 0 5 18 V
ID(RMS) Drain RMS current 38 A
Positive source current LDO5V 25 mA
RRDRV
 		 RDRV to GND resistance from external slew-rate control resistor 0 500 kΩ
CVNEG
 		 VNEG to GND capacitance from external bypass capacitor at bias 1 10 uF
LBBSW
 		 BBSW to GND inductance from external buck-boost inductor 3 4.7 10 uH
TJ Operating Junction temperature -40 125 °C
(1) Transient ringing peak voltage after device turn-off.  Peak voltage damped to ≤ 520 V within 1 µs.
(2) Driver must be ready to operate and IN pin must be kept at logic "0" during the common mode transient.