JAJSKT9A December   2020  – June 2021 PCMD3140

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: I2C Interface
    7. 6.7  Switching Characteristics: I2C Interface
    8. 6.8  Timing Requirements: TDM, I2S or LJ Interface
    9. 6.9  Switching Characteristics: TDM, I2S or LJ Interface
    10. 6.10 Timing Requirements: PDM Digital Microphone Interface
    11. 6.11 Switching Characteristics: PDM Digial Microphone Interface
    12. 6.12 Timing Diagrams
    13. 6.13 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Serial Interfaces
        1. 7.3.1.1 Control Serial Interfaces
        2. 7.3.1.2 Audio Serial Interfaces
          1. 7.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 7.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 7.3.1.2.3 Left-Justified (LJ) Interface
        3. 7.3.1.3 Using Multiple Devices With Shared Buses
      2. 7.3.2 Phase-Locked Loop (PLL) and Clock Generation
      3. 7.3.3 Reference Voltage
      4. 7.3.4 Microphone Bias
      5. 7.3.5 Digital PDM Microphone Record Channel
      6. 7.3.6 Signal-Chain Processing
        1. 7.3.6.1 Programmable Digital Volume Control
        2. 7.3.6.2 Programmable Channel Gain Calibration
        3. 7.3.6.3 Programmable Channel Phase Calibration
        4. 7.3.6.4 Programmable Digital High-Pass Filter
        5. 7.3.6.5 Programmable Digital Biquad Filters
        6. 7.3.6.6 Programmable Channel Summer and Digital Mixer
        7. 7.3.6.7 Configurable Digital Decimation Filters
          1. 7.3.6.7.1 Linear Phase Filters
            1. 7.3.6.7.1.1 Sampling Rate: 7.35 kHz to 8 kHz
            2. 7.3.6.7.1.2 Sampling Rate: 14.7 kHz to 16 kHz
            3. 7.3.6.7.1.3 Sampling Rate: 22.05 kHz to 24 kHz
            4. 7.3.6.7.1.4 Sampling Rate: 29.4 kHz to 32 kHz
            5. 7.3.6.7.1.5 Sampling Rate: 44.1 kHz to 48 kHz
            6. 7.3.6.7.1.6 Sampling Rate: 88.2 kHz to 96 kHz
            7. 7.3.6.7.1.7 Sampling Rate: 176.4 kHz to 192 kHz
            8. 7.3.6.7.1.8 Sampling Rate: 352.8 kHz to 384 kHz
            9. 7.3.6.7.1.9 Sampling Rate: 705.6 kHz to 768 kHz
          2. 7.3.6.7.2 Low-Latency Filters
            1. 7.3.6.7.2.1 Sampling Rate: 14.7 kHz to 16 kHz
            2. 7.3.6.7.2.2 Sampling Rate: 22.05 kHz to 24 kHz
            3. 7.3.6.7.2.3 Sampling Rate: 29.4 kHz to 32 kHz
            4. 7.3.6.7.2.4 Sampling Rate: 44.1 kHz to 48 kHz
            5. 7.3.6.7.2.5 Sampling Rate: 88.2 kHz to 96 kHz
            6. 7.3.6.7.2.6 Sampling Rate: 176.4 kHz to 192 kHz
          3. 7.3.6.7.3 Ultra-Low-Latency Filters
            1. 7.3.6.7.3.1 Sampling Rate: 14.7 kHz to 16 kHz
            2. 7.3.6.7.3.2 Sampling Rate: 22.05 kHz to 24 kHz
            3. 7.3.6.7.3.3 Sampling Rate: 29.4 kHz to 32 kHz
            4. 7.3.6.7.3.4 Sampling Rate: 44.1 kHz to 48 kHz
            5. 7.3.6.7.3.5 Sampling Rate: 88.2 kHz to 96 kHz
            6. 7.3.6.7.3.6 Sampling Rate: 176.4 kHz to 192 kHz
            7. 7.3.6.7.3.7 Sampling Rate: 352.8 kHz to 384 kHz
      7. 7.3.7 Voice Activity Detection (VAD)
      8. 7.3.8 Interrupts, Status, and Digital I/O Pin Multiplexing
    4. 7.4 Device Functional Modes
      1. 7.4.1 Sleep Mode or Software Shutdown
      2. 7.4.2 Active Mode
      3. 7.4.3 Software Reset
    5. 7.5 Programming
      1. 7.5.1 Control Serial Interfaces
        1. 7.5.1.1 I2C Control Interface
          1. 7.5.1.1.1 General I2C Operation
          2. 7.5.1.1.2 I2C Single-Byte and Multiple-Byte Transfers
            1. 7.5.1.1.2.1 I2C Single-Byte Write
            2. 7.5.1.1.2.2 I2C Multiple-Byte Write
            3. 7.5.1.1.2.3 I2C Single-Byte Read
            4. 7.5.1.1.2.4 I2C Multiple-Byte Read
    6. 7.6 Register Maps
      1. 7.6.1 Page 0 Registers
      2. 7.6.2 Page 1 Registers
      3. 7.6.3 Programmable Coefficient Registers
        1. 7.6.3.1 Programmable Coefficient Registers: Page 2
        2. 7.6.3.2 Programmable Coefficient Registers: Page 3
        3. 7.6.3.3 Programmable Coefficient Registers: Page 4
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Four-Channel Digital PDM Microphone Recording
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Example Device Register Configuration Script for EVM Setup
        3. 8.2.1.3 Application Curves
    3. 8.3 What to Do and What Not to Do
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.6 Register Maps

This section describes the control registers for the device in detail. All registers are eight bits in width and are allocated to device configuration and programmable coefficients settings. These registers are mapped internally using a page scheme that can be controlled using I2C communication to the device. Each page contains 128 bytes of registers. All device configuration registers are stored in page 0, which is the default page setting at power up (and after a software reset). All programmable coefficient registers are located in page 2, page 3, and page 4. The device current page can be switch to a new desired page by using the PAGE[7:0] bits located in register 0 of every page.

Do not read from or write to reserved pages or reserved registers. Write only default values for the reserved bits in the valid registers.

The procedure for register access across pages is:

  • Select page N (write data N to register 0 regardless of the current page number)
  • Read or write data from or to valid registers in page N
  • Select the new page M (write data M to register 0 regardless of the current page number)
  • Read or write data from or to valid registers in page M
  • Repeat as needed