JAJSF26E March   2018  – August 2021 TMP1075

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 概要 (続き)
  6. 6 Device Comparison
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  Electrical Characteristics:TMP1075
    6. 8.6  Electrical Characteristics: TMP1075N
    7. 8.7  Timing Requirements:TMP1075
    8. 8.8  Timing Requirements: TMP1075N
    9. 8.9  Switching Characteristics
    10. 8.10 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Digital Temperature Output
      2. 9.3.2 I2C and SMBus Serial Interface
        1. 9.3.2.1  Bus Overview
        2. 9.3.2.2  Serial Bus Address
        3. 9.3.2.3  Pointer Register
          1. 9.3.2.3.1 Pointer Register Byte [reset = 00h]
        4. 9.3.2.4  Writing and Reading to the TMP1075
        5. 9.3.2.5  Operation Mode
          1. 9.3.2.5.1 Receiver Mode
          2. 9.3.2.5.2 Transmitter Mode
        6. 9.3.2.6  SMBus Alert Function
        7. 9.3.2.7  General Call- Reset Function
        8. 9.3.2.8  High-Speed Mode (HS)
        9. 9.3.2.9  Coexists in I3C Mixed Fast Mode
        10. 9.3.2.10 Time-Out Function
      3. 9.3.3 Timing Diagrams
      4. 9.3.4 Two-Wire Timing Diagrams
    4. 9.4 Device Functional Modes
      1. 9.4.1 Shutdown Mode (SD)
      2. 9.4.2 One-Shot Mode (OS)
      3. 9.4.3 Continuous Conversion Mode (CC)
      4. 9.4.4 Thermostat Mode (TM)
        1. 9.4.4.1 Comparator Mode (TM = 0)
        2. 9.4.4.2 Interrupt Mode (TM = 1)
        3. 9.4.4.3 Polarity Mode (POL)
    5. 9.5 Register Map
      1. 9.5.1 Register Descriptions
        1. 9.5.1.1 Temperature Register (address = 00h) [default reset = 0000h]
        2. 9.5.1.2 Configuration Register (address = 01h) [default reset = 00FFh (60A0h TMP1075N)]
        3. 9.5.1.3 Low Limit Register (address = 02h) [default reset = 4B00h]
        4. 9.5.1.4 High Limit Register (address = 03h) [default reset = 5000h]
        5. 9.5.1.5 Device ID Register (address = 0Fh) [default reset = 7500]
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Migrating From the xx75 Device Family
      3. 10.2.3 Application Curve
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Receiving Notification of Documentation Updates
    2. 13.2 サポート・リソース
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

4 Revision History

Changes from Revision D (October 2019) to Revision E (August 2021)

  • TMP1075N の特長を一覧に追加Go
  • 「特長」の一覧に標準精度の仕様を追加Go
  • SOT563 (TMP1075N 注文可能) パッケージを追加Go
  • 「概要」に TMP1075N の温度範囲を追加（続きのセクション）Go
  • Added Device Comparison SectionGo
  • Added figures for different package optionsGo
  • Added column for TMP1075N pin numbersGo
  • Added TMP1075N SpecificationsGo
  • Added TMP1075NDRL Temperature Error vs. Temperature graph Go
  • Added TMP1075N information in Overview SectionGo
  • Changed the Functional Block Diagram to apply to TMP1075NGo
  • Added number of I2C addresses available on TMP1075N to Serial Bus Address Section. Go
  • Added table for TMP1075N address options. Go
  • Updated internal register structure figure to apply to TMP1075NGo
  • Added typical specification for TMP1075N timeout Go
  • Added clarification on timeout function to include SCLGo
  • Removed redundant information to accurate describe all packagesGo
  • Added TMP1075N OS bit behaviorGo
  • Added TMP1075N Continuous Conversion Mode informationGo
  • Updated Conversion Rate Diagram to reflect all TMP1075 and TMP1075NGo
  • Clarified what TM bit behavior for TMP1075 and TMP1075N Go
  • Added table note to indicate Device ID register is not available on TMP1075NGo
  • Added TMP1075N configuration register information Go
  • Updated text to indicate that device ID register does not apply to TMP1075NGo
  • Added number of I2C addresses available on TMP1075NGo
  • Changed Typical Connections figure to apply to TMP1075NGo
  • Removed redundant Application Curve sectionGo
  • Updated text to include TMP1075N informationGo
  • Updated Migrating From the xx75 Device Family section to specify TMP1075 compatible packages Go
  • Included TMP1075N information to Power Supply RecommendationsGo
  • Added figures to the Layout Example section for each packageGo

Changes from Revision C (January 2019) to Revision D (October 2019)

  • 「特長」の一覧にソフトウェア互換性を追加Go
  • Updated absolute max for Power supply V+ to 6.5V from 6VGo
  • Updated absolute max for Input voltage on SCL, SDA, A1, A0 to 6.5V from 6VGo
  • Updated pointer register to be part of the serial interface descriptionGo
  • Updated the register map table to new formatGo
  • Added access type codes for register bitsGo
  • Updated temperature register format and bit definition tableGo
  • Updated configuration register format and bit definition table Go
  • Updated low limit register format and bit definition table Go
  • Updated high limit register format and bit definition table Go
  • Updated device ID register format and bit definition table Go

Changes from Revision B (December 2018) to Revision C (January 2019)

  • TMP1075DSG パッケージをプレビューから量産データに変更Go
  • 「温度精度 (DGK & D)」グラフで、最小/最大限界値を 1.5℃から 1℃に変更Go
  • Changed min/max limit from 1.5°C to 1°C in the DGK & D Temperature Error vs. Temperature graphGo
  • Added DSG Temperature Error vs. Temperature graph Go

Changes from Revision A (June 2018) to Revision B (December 2018)

  • TMP1075DSG パッケージを追加Go
  • データシートの「概要」セクションを更新し、「概要 (続き)」セクションを追加Go
  • Added TMP1075 configuration register support for single byte read and writeGo
  • Added Software support section for migrating from xx75 to TMP1075 Go

Changes from Revision * (March 2018) to Revision A (June 2018)

  • TMP1075DGK の注文ステータスを「事前情報」から「量産データ」に変更Go
  • SOIC および DFN パッケージを追加Go
  • Changed the Functional Block Diagram Go
  • Changed Digital Temperature Output crossreference from: Temperature Register (0x00) to: Temperature Data Format Go
  • Changed the Temperature Data Format table Go
  • Changed and renamed the Address Pins and Slave Addresses for the TMP1075 table to Address Pins State Go
  • Changed the Two-Wire Timing Diagrams section Go
  • Added content to the Device Functional Modes section Go