狭帯域システム向け、高性能 Sub-1GHz ワイヤレス・トランシーバ
製品の詳細
パラメータ
パッケージ|ピン|サイズ
特長
- High-Performance, Single-Chip Transceiver
- Adjacent Channel Selectivity:
64 dB at 12.5-kHz Offset - Blocking Performance: 91 dB at 10 MHz
- Excellent Receiver Sensitivity:
- –123 dBm at 1.2 kbps
- –110 dBm at 50 kbps
- –127 dBm Using Built-in Coding Gain
- Very Low Phase Noise:
–111 dBc/Hz at 10-kHz Offset
- Adjacent Channel Selectivity:
- Suitable for Systems Targeting ETSI Category 1
Compliance in 169-MHz and 433-MHz Bands - High Spectral Efficiency (9.6 kbps in 12.5-kHz
Channel in Compliance With FCC Narrowbanding
Mandate) - Separate 128-Byte RX and TX FIFOs
- Support for Seamless Integration With the CC1190
Device for Increased Range Giving up to 3-dB
Improvement in Sensitivity and up to +27-dBm
Output Power - Power Supply
- Wide Supply Voltage Range (2.0 V to 3.6 V)
- Low Current Consumption:
- RX: 2 mA in RX Sniff Mode
- RX: 17 mA Peak Current in Low-Power
Mode - RX: 22 mA Peak Current in
High-Performance Mode - TX: 45 mA at +14 dBm
- Power Down: 0.12 µA
(0.5 µA With eWOR Timer Running)
- Programmable Output Power up to +16 dBm With
0.4-dB Step Size - Automatic Output Power Ramping
- Configurable Data Rates: 0 to 200 kbps
- Supported Modulation Formats: 2-FSK,
2-GFSK, 4-FSK, 4-GFSK, MSK, OOK - WaveMatch: Advanced Digital Signal Processing
for Improved Sync Detect Performance - RoHS-Compliant 5-mm × 5-mm No-Lead QFN
32-Pin Package (RHB) - Regulations – Suitable for Systems Targeting
Compliance With- Europe: ETSI EN 300 220, ETSI EN 54-25
- US: FCC CFR47 Part 15, FCC CFR47 Part 90,
24, and 101 - Japan: ARIB RCR STD-T30,
ARIB STD-T67, ARIB STD-T108
- Peripherals and Support Functions
- Enhanced Wake-On-Radio (eWOR)
Functionality for Automatic Low-Power Receive
Polling - Includes Functions for Antenna Diversity Support
- Support for Retransmissions
- Support for Automatic Acknowledge of Received
Packets - TCXO Support and Control, Also in Power
Modes - Automatic Clear Channel Assessment (CCA) for
Listen-Before-Talk (LBT) Systems - Built-in Coding Gain Support for Increased
Range and Robustness - Digital RSSI Measurement
- Temperature Sensor
- Enhanced Wake-On-Radio (eWOR)
概要
The CC1120 device is a fully integrated single-chip radio transceiver designed for high performance at very low-power and low-voltage operation in cost-effective wireless systems. All filters are integrated, thus removing the need for costly external SAW and IF filters. The device is mainly intended for Industrial, Scientific, and Medical (ISM) applications and Short Range Device (SRD) frequency bands at 164 to 192 MHz, 274 to 320 MHz, 410 to 480 MHz, and 820 to 960 MHz.
The CC1120 device provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio. The main operating parameters of the CC1120 device can be controlled through an SPI interface. In a typical system, the CC1120 device is used with a microcontroller and only a few external passive components.
技術資料
設計と開発
追加の事項や他のリソースを参照するには、以下のタイトルをクリックすると、詳細ページを表示できます。ハードウェア開発
概要
CC1120-CC1190 ブースタパック・モジュールは、MSP-EXP430F5529 および MSP-EXP430G2553 ローンチパッド開発キットで使用できます。また、SmartRF Studio アプリケーション・ソフトウェアを使用することにより、スタンドアローン・モジュールとして機能します。また、このモジュールは、米国の Sigfox ワイヤレス・ネットワークでの使用が認定されており、Sigfox から有効なライセンスを取得しています。このモジュールは、米国の 902 ~ 928MHz およびヨーロッパの 869 ~ 870MHz ISM 周波数帯域で動作する内蔵 PCB パターン・アンテナを装備しています。
特長
- ローンチパッドおよび SmartRF Studio アプリケーションの両方で使用可能
- 米国の Sigfox ワイヤレス・ネットワークでの使用が認定済み
- 同じ設計で BOM コスト を少し変更するだけで 915MHz と 868MHz の両方の周波数帯域で使用可能
- 同じ設計で BOM コスト を少し変更するだけで CC112x デバイスと CC12xx デバイスで使用可能
- 内蔵 PCB パターン・アンテナ
概要
SmartRF Transceiver 評価ボード(TrxEB)は、評価、性能テスト、ソフトウェア開発のため、TI のローパワー RF トランシーバと組み合わせて使用します。
以下のトランシーバ評価モジュールがサポートされています。
- CC1101EM*
- CC11xLEM*
- CC112xEM*
- CC1175EM*
- CC1200EM*
- CC2500EM
- CC2520EM
(*) すべての周波数派生版、および CC1190 との組み合わせもサポートされています
評価モジュールは、TI ストアで別売りの EMK(評価モジュール・キット)の形で入手できます
SmartRF TrxEB を使用して実行できる作業
- MSP430F5438A マイコンでの無線プロトコルの開発。関連するトランシーバの Web ページに掲載されているコード・サンプルの参照。
- SmartRF Studio を使用したトランシーバの性能評価。
- TrxEB+EM を使用して得られた結果と、独自ハードウェアから得られた結果の比較。
- 独自ボードの無線を TrxEB に接続し、既知の正常に動作するソフトウェアを使用して独自の RF 設計をテスト。その後、SmartRF Studio を使用して無線の実験。
- 独自ボード上のマイコンを TrxEB に実装されているブレークアウト・ピン 経由でトランシーバ EM に接続し、既知の正常に動作する RF ハードウェアを使用して独自ソフトウェアをテスト。
ボードの最新情報については、SmartRF TrxEB ユーザーズ・ガイドを参照してください。このガイドでは、ドライバのインストール方法、ボードに実装されているペリフェラルの詳細、トランシーバ評価モジュールとのインターフェイス確立方法について説明しています。
特長
- MSP430F5438A マイコン
- 64 x 128 ピクセルのシリアル LCD
- 4 個の汎用 LED
- 5 個の押しボタン
- 256KB のシリアル Flash
- 3 軸デジタル加速度計
- 周辺光センサ
- 電流測定用のジャンパ
- ブレークアウト・ピン
- フルスピード USB 2.0 インターフェイス
- SmartRF Studio のサポート
概要
概要
The CC1120 Evaluation Module Kit for 169MHz can be used in conjunction with the CC1120 Development Kit to evaluate the performance of the Perfomance Line RF-IC at this particular frequency. The CC1120DK is required for operation and needs to be ordered separately.
This is not available in the United (...)
特長
Kit contents:
- 2 x CC1120 Evaluation Modules for 169 MHz
- Whip antennas from Pulse
Complete RF reference designs for the evaluation modules are available online.
概要
The CC1120 Evaluation Module Kit for 420-470 MHz can be used in conjunction with the CC1120 Development Kit to evaluate the performance of the Perfomance Line RF-IC at this particular frequency. The CC1120DK is required for operation and needs to be ordered separately.
This CC1120 Evaluation Module (...)
特長
Kit contents:
- 2 x CC1120 Evaluation Modules for 420-470 MHz
- Whip antennas
Complete RF reference designs for the evaluation modules are available online.
概要
特長
- 2 x CC1120 Evaluation Modules for 868-915 MHz
- Whip antennas
Complete RF reference designs for the evaluation modules are available online.
概要
The CC Debugger is a small programmer and debugger for the TI Low Power RF System-on-Chips. It can be used together with IAR Embedded Workbench for 8051 (version 7.51A or later) for debugging and SmartRF Flash Programmer for flash programming. The CC Debugger can also be used for controlling (...)
特長
Contents in the box:
- CC Debugger
- Mini USB cable
- 10-pin flat cable with 2x5 2.54mm connector
- 10-pin flat cable with 2x5 1.27mm connector
- Converter board 2.54mm-1.27mm connector
- Documentation
CC-Debugger can be used to program and debug the following 8051-based system-on-chips from Texas Instruments:
- CC1110 (...)
概要
The CC1120 development kit provides a complete hardware performance testing and software development platform for TI's Sub-1 GHz Performance Line devices. The development kit comes with a pre-programmed packet error rate test. RF range and robustness can be tested with different RF settings, and (...)
特長
- 2 x SmartRF Transceiver EB (TrxEB)
- 2 x CC1120EM 868/915 MHz
- 2 x Pulse Antennas
- 1 x MSP430 Debug Probe (FET)
- 2 x Micro USB Cables
- 1 x Standard USB Cable
- 1 x 14-pin Flat Cable
- 4 x 1.5 Volt AA Batteries
- Documentation
概要
This BoosterPack kit contains one "EM Adapter BoosterPack". The purpose of the EM adapter board is to provide an-easy-to-use bridge between any of the TI MCU LaunchPads and the wide variety of TI RF evaluation modules (EM), for instance the CCxxxx Low-Power RF evaluation modules. No specific (...)
特長
- Evaluation Module (EM) connectors supporting all EMs from Texas Instruments
- Dual-row LaunchPad (LP) connectors, allowing stacking of XL BoosterPacks
- USB power supply to support assemblies drawing more current than the LaunchPad is able to source alone
- Buck/boost voltage regulator, allowing any power (...)
ソフトウェア開発
特長
- Uni-directional S1-,.T1- and C1-mode Meter configuration at 868 MHz
- Bi-directional S2-, T2- and C2-mode Meter configuration at 868 MHz
- Bi-directional S2-, T2- and C2-mode Data Collector configuration at 868 MHz
- 115.2 kbps UART interface with Serial Command Interpreter (to external Host MCU)
- API (...)
設計ツールとシミュレーション
特長
- Based on our TI wireless technology supporting Wi-Fi®, Bluetooth®, Zigbee®, Sub-1 GHz, Sigfox, 2.4 GHz ,multi-band connectivity and more
- Integrates clocks, SPI flash and passive components
- Years of successful collaboration
- Includes hardware customization, software integration and cloud services
- Links to (...)
SmartRF Packet Sniffer 2
SmartRF Packet Sniffer 2 includes software and firmware to capture and display over-the-air packets. The capture device is connected to the PC via USB. SmartRF Packet Sniffer 2 supports the CC13xx and CC26xx family of devices as capture device and uses Wireshark for packet (...)
特長
- Sub-1GHz デバイスと 2.4GHz デバイス向けの距離概算スプレッドシート
- 距離デバッグ・チェックリスト
特長
- リンク・テスト:ノード間でパケットを送受信します。
- アンテナ / 放射線試験:連続波の TX と RX 状態で無線を設定します。
- 全製品に対するレジスタの推奨 / 代表値。
- 個別の RF レジスタの読み取りと書き込みを行います。
- 無線制御のために個別のコマンドを実行します。
- 各レジスタまたはコマンドのビット・フィールドに関する詳細情報。
- ファイルからデバイス構成データの保存と読み込みを行います。
- レジスタの設定値とコマンド引数を、ユーザー定義可能なフォーマットにエクスポートします。
- 無線構成コードをエクスポートします(CC13xx、CC26xx)。
- カスタム GPIO 構成を可能にします(CC13xx、CC26xx)。
- デバッグ・プローブまたは評価ボードを通じて、USB 経由で複数の評価ボードと通信します。
- 単一のコンピュータで最大 32 の評価ボードをサポートします。
互換性に関する問題
SmartRF Studio 6 は、Microsoft® Windows 98、Windows 2000、Windows XP (32 ビット)、Windows Vista (32 ビット)、Windows 7 (32 ビット) の各環境で動作します。
SmartRF Studio 7 は、32 ビット版と 64 ビット版の Microsoft® Windows 7、8、10 で動作します。
インストール手順:
- 該当 ZIP ファイルをハード・ディスクにダウンロードします。
- そのファイルを解凍します。
- readme.txt ファイルを読み、このリリースに関する情報を参照します。
- 手順に従ってセットアップ・ファイルを実行します。
リファレンス・デザイン
CAD/CAE シンボル
パッケージ | ピン数 | ダウンロード |
---|---|---|
VQFN (RHB) | 32 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL rating/ リフローピーク温度
- MTBF/FIT の推定値
- 原材料組成
- 認定試験結果
- 継続的な信頼性モニタ試験結果
おすすめの製品には、この TI 製品に関連するパラメータ、評価モジュール、またはリファレンス・デザインが含まれている場合があります。