トップ

製品の詳細

パラメータ

Function Clock generator Number of outputs 10 Output frequency (Max) (MHz) 1500 VCC core (V) 3.3 VCC out (V) 3.3 Input type LVCMOS, LVPECL Output type LVCMOS, LVDS, LVPECL Operating temperature range (C) -40 to 85 Features Integrated EEPROM, Programmable phase offset Rating Catalog open-in-new その他の クロック・ジェネレータ

パッケージ|ピン|サイズ

VQFN (RGC) 64 81 mm² 9 x 9 open-in-new その他の クロック・ジェネレータ

特長

  • High Performance LVPECL, LVDS, LVCMOS PLL Clock Synchronizer
  • Two Reference Clock Inputs (Primary and Secondary Clock) for Redundancy
    Support with Manual or Automatic Selection
  • Accepts Two Differential Input (LVPECL or LVDS) References up to 500MHz
    (or Two LVCMOS Inputs up to 250MHz) as PLL Reference
  • VCXO_IN Clock is Synchronized to One of Two Reference Clocks
  • VCXO_IN Frequencies up to 1.5GHz (LVPECL)
    800MHz for LVDS and
    250MHz for LVCMOS Level Signaling
  • Outputs Can be a Combination of LVPECL, LVDS, and LVCMOS
    (Up to 10 Differential LVPECL or LVDS Outputs or up to
    20 LVCMOS Outputs), Output 9 can be Converted to an
    Auxiliary Input as a 2nd VC(X)O.
  • Output Divider is Selectable to Divide by 1, 2, 3, 4, 5, 6, 8, 10,
    12, 16, 18, 20, 24, 28, 30, 32, 36, 40, 42, 48, 50, 56, 60, 64, 70,
    or 80 On Each Output Individually up to Eight Dividers. (Except for
    Output 0 and 9, Output 0 Follows Output 1 Divider and Output 9
    Follows Output 8 Divider)
  • SPI Controllable Device Setting
  • Individual Output Enable Control via SPI Interface
  • Integrated On-Chip Non-Volatile Memory (EEPROM) to Store Settings
    without the Need to Apply High Voltage to the Device
  • Optional Configuration Pins to Select Between Two Default Settings
    Stored in EEPROM
  • Efficient Jitter Cleaning from Low PLL Loop Bandwidth
  • Very Low Phase Noise PLL Core
  • Programmable Phase Offset (Input Reference to Outputs)
  • Wide Charge-Pump Current Range From 200µA to 3mA
  • Presets Charge-Pump to VCC_CP/2 for Fast Center-Frequency
    Setting of VC(X)O, Controlled Via the SPI Bus
  • SERDES Startup Mode (Depending on VCXO Range)
  • Auxiliary Input: Output 9 can Serve as 2nd VCXO Input to Drive
    All Outputs or to Serve as PLL Feedback Signal
  • RESET or HOLD Input Pin to Serve as Reset or Hold Functions
  • REFERENCE SELECT for Manual Select Between Primary and Secondary
    Reference Clocks
  • POWER DOWN (PD) to Put Device in Standby Mode
  • Analog and Digital PLL Lock Indicator
  • Internally Generated VBB Bias Voltages for Single-Ended Input Signals
  • Frequency Hold-Over Mode Activated by HOLD Pin or SPI Bus to Improve
    Fail-Safe Operation
  • Input to All Outputs Skew Control
  • Individual Skew Control for Each Output with Each Output Divider
  • Packaged in a QFN-64 Package
  • ESD Protection Exceeds 2kV HBM
  • Industrial Temperature Range of –40°C to 85°
open-in-new その他の クロック・ジェネレータ

概要

The CDCE72010 is a high-performance, low phase noise, and low skew clock synchronizer that synchronizes a VCXO (Voltage Controlled Crystal Oscillator) or VCO (Voltage Controlled Oscillator) frequency to one of two reference clocks. The clock path is fully programmable providing the user with a high degree of flexibility. The following relationship applies to the dividers:

Frequency (VCXO_IN or AUX_IN) / Frequency (PRI_REF or SEC_REF) = (P*N)/(R*M)

The VC(X)O_IN clock operates up to 1.5GHz through the selection of external VC(X)O and loop filter components. The PLL loop bandwidth and damping factor can be adjusted to meet different system requirements.

The CDCE72010 can lock to one of two reference clock inputs (PRI_REF and SEC_REF) and supports frequency hold-over mode for fail-safe and system redundancy. The outputs of the CDCE72010 are user definable and can be any combination of up to 10 LVPECL/LVDS outputs or up to 20 LVCMOS outputs. The built-in synchronization latches ensure that all outputs are synchronized for very low output skew.

All device settings, including output signaling, divider value selection, input selection, and many more, are programmable with the SPI (4-wire Serial Peripheral Interface). The SPI allows individual control of the device settings.

The device operates in a 3.3V environment and is characterized for operation from –40°C to +85°C.

The CDCE72010 is available in a 64-pin lead-free “green” plastic quad flatpack package with enhanced bottom thermal pad for heat dissipation. The Texas Instruments package designator is RGC (S-PQFP-N64).

open-in-new その他の クロック・ジェネレータ
ダウンロード

技術資料

= 主要な資料
結果が見つかりませんでした。検索条件をクリアして、もう一度検索を行ってください。 すべて表示 18
種類 タイトル 英語版のダウンロード 日付
* データシート Ten Output High Performance Clock Synchronizer, Jitter Cleaner &Clock Distrib データシート 2012年 1月 31日
アプリケーション・ノート Q3 2009 Issue Analog Applications Journal 2018年 9月 24日
技術記事 How to select an optimal clocking solution for your FPGA-based design 2015年 12月 9日
ユーザー・ガイド ADS42B4x - User's Guide 2015年 1月 30日
技術記事 Clocking sampled systems to minimize jitter 2014年 7月 31日
技術記事 Timing is Everything: How to optimize clock distribution in PCIe applications 2014年 3月 28日
ユーザー・ガイド AFE722xEVM User's Guide 2013年 2月 5日
ユーザー・ガイド TSW3725 User's Guide 2011年 10月 25日
アプリケーション・ノート 3Q 2011 Issue Analog Applications Journal 2011年 9月 16日
アプリケーション・ノート Clock jitter analyzed in the time domain, Part 3 2011年 9月 16日
アプリケーション・ノート Analog Applications Journal 3Q 2011 2011年 9月 1日
アプリケーション・ノート 4Q 2010 Issue Analog Applications Journal 2010年 11月 15日
アプリケーション・ノート Clock jitter analyzed in the time domain, Part 2 2010年 11月 15日
アプリケーション・ノート Impact of sampling-clock spurs on ADC performance 2009年 7月 14日
アプリケーション・ノート CDCE72010 as clocking solution for High Speed Analog-to-Digital Converters 2008年 6月 8日
アプリケーション・ノート Phase Noise Performance and Jitter Cleaning Ability of CDCE72010 2008年 6月 2日
アプリケーション・ノート CDCE72010 as Frequency Synthesizer 2008年 5月 31日
ユーザー・ガイド CDCE72010 EVM 2008年 5月 30日

設計と開発

追加の事項や他のリソースを参照するには、以下のタイトルをクリックすると、詳細ページを表示できます。

ハードウェア開発

評価基板 ダウンロード
document-generic ユーザー・ガイド
概要

The ADS4122EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4122 device, an extremely low power 12-bit 65 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4125EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4125 device, an extremely low power 12-bit 125 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4126EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4126 device, an extremely low power 12-bit 160 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4129EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' ADS4129 device, an extremely low power 12-bit 250 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible environment to (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4142EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4142 device, an extremely low power 14-bit 65 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4145EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4145 device, an extremely low power 14-bit 125 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4146EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4146 device, an extremely low power 14-bit 160 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a flexible (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1405EVM capture card
  • USB (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    $299.00
    概要

    The ADS41B25EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS41B25 device, an extremely low power 12-bit 125 MSPS analog to digital converter with integrated high-impedance input buffer. The ADC features a configurable parallel DDR LVDS or CMOS (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    $299.00
    概要

    The ADS41B29EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS41B29 device, an extremely low power 12-bit 250 MSPS analog to digital converter with integrated high-impedance input buffer. The ADC features a configurable parallel DDR LVDS or CMOS (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要
  • The ADS4229EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4229 device, an extremely low power dual channel 12-bit 250 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)
  • 特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4242EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4242 device, an extremely low power dual channel 14-bit 65 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4245EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4245 device, an extremely low power dual channel 14-bit 125 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4246EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4246 device, an extremely low power dual channel 14-bit 160 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS4249EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4249 device, an extremely low power dual channel 14-bit 250 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)

    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS5481EVM is a circuit board which allows the designer to run an evaluation of Texas Instruments’ ADS5481 device, a 16-bit 80 MSPS ADC with DDR LVDS outputs. With the supplied logic analyzer breakout board, the ADC LVDS output can be directly captured using either an Agilent E5405A or (...)

    特長

    Transformer coupled analog input path CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit DDR LVDS output and capture ability

    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS5482EVM is a circuit board which allows the designer to run an evaluation of Texas Instruments’ ADS5482 device, a 16-bit 105 MSPS ADC with DDR LVDS outputs. With the supplied logic analyzer breakout board, the ADC LVDS output can be directly captured using either an Agilent E5405A or (...)

    特長

    Transformer coupled analog input path CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit DDR LVDS output and capture ability

    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS5483EVM is a circuit board which allows the designer to run an evaluation of Texas Instruments’ ADS5483 device, a 16-bit 135 MSPS ADC with DDR LVDS outputs. With the supplied logic analyzer breakout board, the ADC LVDS output can be directly captured using either an Agilent E5405A or (...)

    特長
    • Transformer coupled analog input path
    • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
    • DDR LVDS output and capture ability
    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS5484EVM is a circuit board which allows the designer to run an evaluation of Texas Instruments’ ADS5484 device, a 16-bit 170 MSPS ADC with DDR LVDS outputs. With the supplied logic analyzer breakout board, the ADC LVDS output can be directly captured using either an Agilent E5405A or (...)

    特長
    • Transformer coupled analog input path
    • CDCE72010 Jitter Clock Synchronizer and
    • Jitter Cleaner clocking circuit
    • DDR LVDS output and capture ability
    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The ADS58C28EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' ADS58C28 device, a dual channel 11-bit 200 MSPS analog to digital converter featuring TI's SNRBoost technology. The ADC EVM features a DDR LVDS data output which is compatible with TI's TSW1200 (...)

    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要
    The AFE7222EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' two-channel AFE7222, a low power analog front end mixed-signal transceiver. The AFE7222 contains dual 12-bit 65MSPS ADCs and dual 12-bit 130MSPS DACs, along with 2x/4x interpolation, /2 (...)
    特長
    • Comprehensive test capability for the AFE7222 for ZIF, IF and RF transmit outputs
    • AFE7222 ZIF or IF ADC receive testing (optional TRF371125EVM can be purchased for RF-to-bits ZIF receiver)
    • Direct connection to TSW1400 pattern generator and capture card (or TSW1405, TSW1406)
    • Includes CDCE72010 for clock (...)
    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    概要

    The AFE7225EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' two-channel AFE7225, a low power analog front end mixed-signal transceiver. The AFE7225 contains dual 12-bit 125MSPS ADCs and dual 12-bit 250MSPS DACs, along with 2x/4x interpolation, /2 (...)

    特長
    • Comprehensive test capability for the AFE7225 for ZIF, IF and RF transmit outputs
    • AFE7225 ZIF or IF ADC receive testing (optional TRF371125EVM can be purchased for RF-to-bits ZIF receiver)
    • Direct connection to TSW1400 pattern generator and capture card (or TSW1405, TSW1406)
    • Includes CDCE72010 for clock (...)
    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    $199.00
    概要

    The CDCE72010EVM is the evaluation module for CDCE72010 - 10 outputs low jitter clock synchornizer. CDCE72010 can be programmed through the SPI interface using the evaluation module (EVM)programming GUI. The evaluation module (EVM) is designed to demonstrate the electrical performance of the (...)

    特長
    • Easy-to-use evaluation board to generate low-phase noise clocks up to 1.5 GHz
    • Easy device programming via host-powered USB port
    • Fast configuration through provided graphical user interface (GUI) software interface
    • Total board power provided either through USB port or separate 3.3 V and ground (...)
    評価基板 ダウンロード
    document-generic ユーザー・ガイド
    $499.00
    概要

    The DAC5688EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' dual-channel 16-bit 800 MSPS digital-to-analog converter (DAC) with wideband LVDS data input, integrated 2x/4x/8x interpolation filters, on-board clock multiplier and PLL, 32-bit NCO and (...)

    特長
    • Comprehensive test capability for DAC5688
    • Direct connection to TSW3100 signal generator EVM
    • Has a programmable Low Jitter Clock Synthesizer capable of working with a VCXO or an external clock source
    • Clock synchronization with TSW3100 for signal integrity
    • Software support with a fully featured GUI for (...)
    評価基板 ダウンロード
    TSW3085EVM
    TSW3085EVM
    document-generic ユーザー・ガイド
    $399.00
    概要

    The TSW3085 Evalutaion Module is a circuit board that allows system designers to evaluate the combined performance of Texas Instruments' transmit signal chain with the LMK04806B (formally National Semiconductor) low noise clock generator/jitter cleaner. For ease of use as a complete RF transmit (...)

    特長
  • Includes LMK04806B for clock generation and jitter cleaning
  • Direct connection to TSW3100 signal generator
  • Comprehensive test capability for the transmitter (DAC3482 dual DAC and TRF3705 IQ Modulator) at analog baseband, IF and RF outputs
  • Software support with a full featured GUI for easy testing and (...)
  • 評価モジュール(EVM)用 GUI ダウンロード
    SCAC100.ZIP (833 KB)

    ソフトウェア開発

    ドライバとライブラリ ダウンロード
    ADS41B49 評価モジュール
    ADS41B49EVM The ADS41B49EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS41B49 device, an extremely low power 14-bit 250 MSPS analog to digital converter with integrated high-impedance input buffer. The ADC features a configurable parallel DDR LVDS or CMOS (...)
    $299.00
    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • ドライバとライブラリ ダウンロード
    ADS4222 評価モジュール
    ADS4222EVM
  • The ADS4222EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4222 device, an extremely low power dual channel 12-bit 65 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)
  • 特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • ドライバとライブラリ ダウンロード
    ADS4225 評価モジュール
    ADS4225EVM The ADS4225EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS4225 device, an extremely low power dual channel 12-bit 125 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs. The EVM provides a (...)
    特長
  • Transformer coupled analog input path
  • Amplifier path based on the THS4509
  • Configurable CMOS or DDR LVDS parallel output modes
  • Transformer coupled clock input path
  • CDCE72010 Jitter Clock Synchronizer and Jitter Cleaner clocking circuit
  • DDR LVDS output and capture ability via TSW1400EVM or TSW1405EVM (...)
  • 設計ツールとシミュレーション

    シミュレーション・モデル ダウンロード
    SCAC103A.ZIP (60 KB) - IBIS Model
    計算ツール ダウンロード
    SCAC104.ZIP (368 KB)

    CAD/CAE シンボル

    パッケージ ピン数 ダウンロード
    VQFN (RGC) 64 オプションの表示

    購入と品質

    サポートとトレーニング

    TI E2E™ Forums (英語) では、TI のエンジニアからの技術サポートが活用できます

    コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください

    TI 製品の品質、パッケージ、ご注文に関する質問は、TI サポートのページをご覧ください。

    トレーニング・シリーズ

    TI のトレーニングとビデオをすべて表示

    ビデオ

    関連ビデオ