製品詳細

CPU C24x Frequency (MHz) 40 Flash memory (kByte) 16 RAM (kByte) 2 ADC resolution (Bps) 10 Sigma-delta filter 8 PWM (Ch) 8 Number of ADC channels 5 Operating temperature range (°C) -40 to 125 Rating Catalog Communication interface CAN, SPI, UART
CPU C24x Frequency (MHz) 40 Flash memory (kByte) 16 RAM (kByte) 2 ADC resolution (Bps) 10 Sigma-delta filter 8 PWM (Ch) 8 Number of ADC channels 5 Operating temperature range (°C) -40 to 125 Rating Catalog Communication interface CAN, SPI, UART
LQFP (VF) 32 81 mm² 9 x 9
  • High-Performance Static CMOS Technology
    • 25-ns Instruction Cycle Time (40 MHz)
    • 40-MIPS Performance
    • Low-Power 3.3-V Design
  • Based on TMS320C2xx DSP CPU Core
    • Code-Compatible With 240x and F243/F241/C242
    • Instruction Set Compatible With F240
  • On-Chip Memory
    • Up to 8K Words x 16 Bits of Flash EEPROM (2 Sectors) (LF2401A)
    • 8K Words x 16 Bits of ROM (LC2401A)
    • Programmable "Code-Security" Feature for the On-Chip Flash/ROM
    • Up to 1K Words x 16 Bits of Data/Program RAM
      • 544 Words of Dual-Access RAM
      • Up to 512 Words of Single-Access RAM
  • Boot ROM
    • SCI Bootloader
  • Event-Manager (EV) Module (EVA), Which Includes:
    • Two 16-Bit General-Purpose Timers
    • Seven 16-Bit Pulse-Width Modulation (PWM) Channels Which Enable:
      • Three-Phase Inverter Control
      • Center- or Edge-Alignment of PWM Channels
      • Emergency PWM Channel Shutdown With External PDPINTA Pin
    • Programmable Deadband (Deadtime) Prevents Shoot-Through Faults
    • One Capture Unit for Time-Stamping of External Events
    • Input Qualifier for Select Pins
    • Synchronized A-to-D Conversion
    • Designed for AC Induction, BLDC, Switched Reluctance, and Stepper Motor Control
  • Small Foot-Print (7 mm × 7 mm) Ideally Suited for Space-Constrained Applications
  • Watchdog (WD) Timer Module
  • 10-Bit Analog-to-Digital Converter (ADC)
    • 5 Multiplexed Input Channels
    • 500 ns Minimum Conversion Time
    • Selectable Twin 8-State Sequencers Triggered by Event Manager
  • Serial Communications Interface (SCI)
  • Phase-Locked-Loop (PLL)-Based Clock Generation
  • Up to 13 Individually Programmable, Multiplexed General-Purpose Input/Output (GPIO) Pins
  • User-Selectable Dual External Interrupts (XINT1 and XINT2)
  • Power Management:
    • Three Power-Down Modes
    • Ability to Power Down Each Peripheral Independently
  • Real-Time JTAG-Compliant Scan-Based Emulation, IEEE Standard 1149.1 (JTAG)
  • Development Tools Include:
    • Texas Instruments (TI) ANSI C Compiler, Assembler/ Linker, and Code Composer Studio™ Debugger
    • Evaluation Modules
    • Scan-Based Self-Emulation (XDS510™)
    • Broad Third-Party Digital Motor Control Support
  • 32-Pin VF Low-Profile Quad Flatpack (LQFP)
  • Extended Temperature Options (A and S)
    • A: –40°C to 85°C
    • S: –40°C to 125°C

Code Composer Studio and XDS510 are trademarks of Texas Instruments.
All trademarks are the property of their respective owners.
IEEE Standard 1149.1-1990, IEEE Standard Test-Access Port; however, boundary scan is not supported in this device family.
TMS320C24x, TMS320C2000, TMS320, and C24x are trademarks of Texas Instruments.
Throughout this document, TMS320Lx2401A is used as a generic name for the TMS320LF2401A and TMS320LC2401A devices. An abbreviated name, Lx2401A, denotes both devices as well.

  • High-Performance Static CMOS Technology
    • 25-ns Instruction Cycle Time (40 MHz)
    • 40-MIPS Performance
    • Low-Power 3.3-V Design
  • Based on TMS320C2xx DSP CPU Core
    • Code-Compatible With 240x and F243/F241/C242
    • Instruction Set Compatible With F240
  • On-Chip Memory
    • Up to 8K Words x 16 Bits of Flash EEPROM (2 Sectors) (LF2401A)
    • 8K Words x 16 Bits of ROM (LC2401A)
    • Programmable "Code-Security" Feature for the On-Chip Flash/ROM
    • Up to 1K Words x 16 Bits of Data/Program RAM
      • 544 Words of Dual-Access RAM
      • Up to 512 Words of Single-Access RAM
  • Boot ROM
    • SCI Bootloader
  • Event-Manager (EV) Module (EVA), Which Includes:
    • Two 16-Bit General-Purpose Timers
    • Seven 16-Bit Pulse-Width Modulation (PWM) Channels Which Enable:
      • Three-Phase Inverter Control
      • Center- or Edge-Alignment of PWM Channels
      • Emergency PWM Channel Shutdown With External PDPINTA Pin
    • Programmable Deadband (Deadtime) Prevents Shoot-Through Faults
    • One Capture Unit for Time-Stamping of External Events
    • Input Qualifier for Select Pins
    • Synchronized A-to-D Conversion
    • Designed for AC Induction, BLDC, Switched Reluctance, and Stepper Motor Control
  • Small Foot-Print (7 mm × 7 mm) Ideally Suited for Space-Constrained Applications
  • Watchdog (WD) Timer Module
  • 10-Bit Analog-to-Digital Converter (ADC)
    • 5 Multiplexed Input Channels
    • 500 ns Minimum Conversion Time
    • Selectable Twin 8-State Sequencers Triggered by Event Manager
  • Serial Communications Interface (SCI)
  • Phase-Locked-Loop (PLL)-Based Clock Generation
  • Up to 13 Individually Programmable, Multiplexed General-Purpose Input/Output (GPIO) Pins
  • User-Selectable Dual External Interrupts (XINT1 and XINT2)
  • Power Management:
    • Three Power-Down Modes
    • Ability to Power Down Each Peripheral Independently
  • Real-Time JTAG-Compliant Scan-Based Emulation, IEEE Standard 1149.1 (JTAG)
  • Development Tools Include:
    • Texas Instruments (TI) ANSI C Compiler, Assembler/ Linker, and Code Composer Studio™ Debugger
    • Evaluation Modules
    • Scan-Based Self-Emulation (XDS510™)
    • Broad Third-Party Digital Motor Control Support
  • 32-Pin VF Low-Profile Quad Flatpack (LQFP)
  • Extended Temperature Options (A and S)
    • A: –40°C to 85°C
    • S: –40°C to 125°C

Code Composer Studio and XDS510 are trademarks of Texas Instruments.
All trademarks are the property of their respective owners.
IEEE Standard 1149.1-1990, IEEE Standard Test-Access Port; however, boundary scan is not supported in this device family.
TMS320C24x, TMS320C2000, TMS320, and C24x are trademarks of Texas Instruments.
Throughout this document, TMS320Lx2401A is used as a generic name for the TMS320LF2401A and TMS320LC2401A devices. An abbreviated name, Lx2401A, denotes both devices as well.

The TMS320Lx2401A device, a new member of the TMS320C24x™ generation of digital signal processor (DSP) controllers, is part of the TMS320C2000™ platform of fixed-point DSPs. The Lx2401A device offers the enhanced TMS320™ DSP architectural design of the C2xx core CPU for low-cost, low-power, and high-performance processing capabilities. Several advanced peripherals, optimized for digital motor and motion control applications, have been integrated to provide a true single-chip DSP controller. While code-compatible with the existing 240x and C24x™ DSP controller devices, the Lx2401A offers increased processing performance (40 MIPS) and a higher level of peripheral integration. See the TMS320x240xA Device Summary section for device-specific features.

The Lx2401A device offers a peripheral suite tailored to meet the specific price/performance points required by various applications. The Lx2401A also offers a cost-effective reprogrammable solution for volume production. A password-based "code security" feature on the device is useful in preventing unauthorized duplication of proprietary code stored in on-chip Flash/ROM. Note that the LF2401A contains a 256-word boot ROM to facilitate in-circuit programming. The boot ROM on LC2401A is used for test purposes.

The Lx2401A offers an event manager module which has been optimized for digital motor control and power conversion applications. Capabilities of this module include center- and/or edge-aligned PWM generation, programmable deadband to prevent shoot-through faults, and synchronized analog-to-digital conversion. Select EV pins have been provided with an "input-qualifier" circuitry, which minimizes inadvertent pin-triggering by glitches.

The high-performance, 10-bit analog-to-digital converter (ADC) has a minimum conversion time of 500 ns and offers up to 5 channels of analog input. The autosequencing capability of the ADC allows a maximum of 16 conversions to take place in a single conversion session without any CPU overhead.

A serial communications interface (SCI) is integrated on all devices to provide asynchronous communication to other devices in the system. To maximize device flexibility, functional pins are also configurable as general-purpose inputs/outputs (GPIOs).

To streamline development time, JTAG-compliant scan-based emulation has been integrated into all devices. This provides non-intrusive real-time capabilities required to debug digital control systems. A complete suite of code-generation tools from C compilers to the industry-standard Code Composer Studio™ debugger supports this family. Numerous third-party developers not only offer device-level development tools, but also system-level design and development support.

NOTE: The Lx2401A device has reduced peripheral functionality compared to other 24x/240x devices. While peripherals such as SPI and CAN are absent on the Lx2401A, peripherals such as EV and ADC have reduced functionality. For example, in the case of EV, there is no QEP unit and the Capture unit has only one capture pin (as opposed to three or six pins in other devices). The ADC has only five input channels (as opposed to eight or sixteen channels in other devices). For these reasons, some bits that are valid in other 24x/240x devices are not applicable in the Lx2401A. The registers and their valid bits are described in Table 16, Lx2401A DSP Peripheral Register Description. For a description of those registers and bits that are valid, refer to the TMS320LF/LC240xA DSP Controllers Reference Guide: System and Peripherals (literature number SPRU357). Any exceptions to SPRU357 has been described in the respective peripheral sections in this data sheet.

The TMS320Lx2401A device, a new member of the TMS320C24x™ generation of digital signal processor (DSP) controllers, is part of the TMS320C2000™ platform of fixed-point DSPs. The Lx2401A device offers the enhanced TMS320™ DSP architectural design of the C2xx core CPU for low-cost, low-power, and high-performance processing capabilities. Several advanced peripherals, optimized for digital motor and motion control applications, have been integrated to provide a true single-chip DSP controller. While code-compatible with the existing 240x and C24x™ DSP controller devices, the Lx2401A offers increased processing performance (40 MIPS) and a higher level of peripheral integration. See the TMS320x240xA Device Summary section for device-specific features.

The Lx2401A device offers a peripheral suite tailored to meet the specific price/performance points required by various applications. The Lx2401A also offers a cost-effective reprogrammable solution for volume production. A password-based "code security" feature on the device is useful in preventing unauthorized duplication of proprietary code stored in on-chip Flash/ROM. Note that the LF2401A contains a 256-word boot ROM to facilitate in-circuit programming. The boot ROM on LC2401A is used for test purposes.

The Lx2401A offers an event manager module which has been optimized for digital motor control and power conversion applications. Capabilities of this module include center- and/or edge-aligned PWM generation, programmable deadband to prevent shoot-through faults, and synchronized analog-to-digital conversion. Select EV pins have been provided with an "input-qualifier" circuitry, which minimizes inadvertent pin-triggering by glitches.

The high-performance, 10-bit analog-to-digital converter (ADC) has a minimum conversion time of 500 ns and offers up to 5 channels of analog input. The autosequencing capability of the ADC allows a maximum of 16 conversions to take place in a single conversion session without any CPU overhead.

A serial communications interface (SCI) is integrated on all devices to provide asynchronous communication to other devices in the system. To maximize device flexibility, functional pins are also configurable as general-purpose inputs/outputs (GPIOs).

To streamline development time, JTAG-compliant scan-based emulation has been integrated into all devices. This provides non-intrusive real-time capabilities required to debug digital control systems. A complete suite of code-generation tools from C compilers to the industry-standard Code Composer Studio™ debugger supports this family. Numerous third-party developers not only offer device-level development tools, but also system-level design and development support.

NOTE: The Lx2401A device has reduced peripheral functionality compared to other 24x/240x devices. While peripherals such as SPI and CAN are absent on the Lx2401A, peripherals such as EV and ADC have reduced functionality. For example, in the case of EV, there is no QEP unit and the Capture unit has only one capture pin (as opposed to three or six pins in other devices). The ADC has only five input channels (as opposed to eight or sixteen channels in other devices). For these reasons, some bits that are valid in other 24x/240x devices are not applicable in the Lx2401A. The registers and their valid bits are described in Table 16, Lx2401A DSP Peripheral Register Description. For a description of those registers and bits that are valid, refer to the TMS320LF/LC240xA DSP Controllers Reference Guide: System and Peripherals (literature number SPRU357). Any exceptions to SPRU357 has been described in the respective peripheral sections in this data sheet.

ダウンロード 字幕付きのビデオを表示 ビデオ

TI からの設計サポートは利用不可能

この製品に関して、新しいコンテンツやソフトウェアの更新など、新規プロジェクトに対する TI からの継続的な設計サポートはありません。該当する場合は、関連する資料、ソフトウェア、ツールはプロダクト フォルダに掲載されています。TI E2ETM サポート フォーラムで、アーカイブ済みの情報を検索することもできます。

お客様が関心を持ちそうな類似品

open-in-new 代替品と比較
比較対象デバイスと類似の機能
TMS320F280023 アクティブ 100MHz、FPU と TMU (三角関数算術演算ユニット) と 64KB フラッシュ搭載、C2000™ 32 ビット・マイコン This product is in the latest generation for high performance C2000 real-time control.

技術資料

star =TI が選定したこの製品の主要ドキュメント
結果が見つかりませんでした。検索条件をクリアしてから、再度検索を試してください。
27 をすべて表示
種類 タイトル 最新の英語版をダウンロード 日付
* データシート TMS320LF2401A, TMS320LC2401A DSP Controllers データシート (Rev. K) 2007年 7月 12日
* エラッタ TMS320LF2401A, TMS320LC2401A DSP Controller Silicon Errata (Rev. G) 2005年 6月 1日
アプリケーション・ノート Semiconductor and IC Package Thermal Metrics (Rev. D) PDF | HTML 2024年 3月 25日
アプリケーション・ノート EEPROM Emulation for Gen 2 C2000 Real-Time MCUs (Rev. A) 2020年 7月 23日
アプリケーション・ノート Development Tool Versions for C2000 Support 2019年 7月 19日
アプリケーション・ノート C2000™ MISRA-C Policy 2017年 9月 26日
アプリケーション・ノート Calculating FIT for a Mission Profile 2015年 3月 24日
その他の技術資料 C2000 リアルタイム・マイコン (Rev. F 翻訳版) 2014年 2月 26日
アプリケーション・ノート 半導体およびICパッケージの熱評価基準 (Rev. B 翻訳版) 最新英語版 (Rev.D) PDF | HTML 2013年 6月 4日
その他の技術資料 C2000 リアルタイム・マイコン (Rev. E 翻訳版) 2012年 10月 25日
アプリケーション・ノート Programming External Nonvolatile Memory Using SDFlash for TMS320C28x Devices 2009年 11月 16日
アプリケーション・ノート Common Object File Format (COFF) 2009年 4月 15日
アプリケーション・ノート Migrating from TMS320x2833x/2823x to TMS320x2834x 2009年 3月 3日
ユーザー・ガイド TMS320x280x, 2801x, 2804x Serial Peripheral Interface (SPI) Reference Guide 2009年 2月 5日
ユーザー・ガイド TMS320x280x, 2801x DSP Enhanced Controller Area Network (eCAN) User's Guide 2009年 1月 22日
アプリケーション・ノート Flash Programming Solutions for the TMS320F28xxx DSCs 2008年 8月 19日
ユーザー・ガイド TMS320x28xx, 28xxx DSP シリアル通信インターフェイス(SCI)リファレンス・ガイド (Rev. B 翻訳版) 最新英語版 (Rev.D) 2008年 6月 12日
アプリケーション・ノート Microstepping Bipolar Drive of Two-Phase Hybrid Stepping Motor on F2808 DSP 2008年 5月 2日
その他の技術資料 デジタル制御電源 ソリューション 2008年 3月 12日
アプリケーション・ノート Using Enhanced Pulse Width Modulator (ePWM) Module for 0-100% Duty Cycle Control 2006年 12月 20日
アプリケーション・ノート Using the eQEP Module in TMS320x280x as a Dedicated Capture 2006年 11月 30日
ユーザー・ガイド TMS320LF/LC240xA DSP Controllers System and Peripherals RG (Rev. C) 2006年 5月 10日
アプリケーション・ノート Average Current Mode Controlled Power Factor Correction Converter..TMS320LF2407A (Rev. A) 2005年 7月 19日
アプリケーション・ノート Online Stack Overflow Detection on the TMS320C28x DSP 2003年 5月 2日
アプリケーション・ノート Getting Started in C and Assembly Code with the TMS320LF240x DSP (Rev. A) 2002年 7月 10日
ユーザー・ガイド TMS320F/C24x DSP Controllers CPU & Instr. Set RG-Manual Update Sheet (SPRU160C) (Rev. A) 2002年 7月 1日
ユーザー・ガイド TMS320F/C24x DSP Controllers CPU and Instruction Set Reference Guide (Rev. C) 1999年 3月 31日

設計と開発

その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。

IDE (統合開発環境)、コンパイラ、またはデバッガ

CCSTUDIO3 — Code Composer Studio(CCS)統合開発環境(IDE)、IDE v3 - 24x/C24x 向け


Code Composer Studio IDE は、組込みアプリケーションの開発とデバッグに使用する一連のツールで構成されています。これは、最適化 C/C++ コンパイラ、ソース・コード・エディタ、プロジェクト・ビルド環境、デバッガ、プロファイラなど、多数の機能を搭載しています。IDE は直感的に使いやすく、アプリケーションの開発フローの各段階を、すべて同一のユーザー・インターフェイスで実行できます。使いやすいツールとインターフェイスが開発の迅速な開始と、高度なツールを活用したアプリケーションへの機能追加を可能にします。

Code Composer Studio (...)

ソフトウェア・プログラミング・ツール

FTLF240X — LF240x フラッシュ・ツール

C2000™ リアルタイム・マイコン TMS320LF240x 向けの各種フラッシュ・ツール
ソフトウェア・プログラミング・ツール

SPRC073 Download LF2401A Serial Flash Programming Utility

lock = 輸出許可が必要 (1 分)
サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
C2000 リアルタイム・マイコン
TMS320LF2401A 40MHz、8kW (キロワード) フラッシュ搭載、32 ピン、16 ビット DSP
ソフトウェア・プログラミング・ツール

SPRC074 Download LF240xA Serial Flash Programming Utility

lock = 輸出許可が必要 (1 分)
サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
C2000 リアルタイム・マイコン
TMS320LF2401A 40MHz、8kW (キロワード) フラッシュ搭載、32 ピン、16 ビット DSP TMS320LF2402A 40MHz、8kW (キロワード) フラッシュ搭載、64 ピン、16 ビット DSP TMS320LF2403A 40MHz、16kW (キロワード) フラッシュ搭載、64 ピン、16 ビット DSP TMS320LF2406A 40MHz、32kW (キロワード) フラッシュ搭載、100 ピン、16 ビット DSP TMS320LF2407A 40MHz、32kW (キロワード) フラッシュ搭載、144 ピン、16 ビット DSP
サポート・ソフトウェア

SPRC141 TMS320LF240x/LF240A Flash API

サポート対象の製品とハードウェア

サポート対象の製品とハードウェア

製品
C2000 リアルタイム・マイコン
SM320LF2407A-EP 40MIPS、C2000™ エンハンスド製品、16 ビット・マイコン (MCU) TMS320LF2401A 40MHz、8kW (キロワード) フラッシュ搭載、32 ピン、16 ビット DSP TMS320LF2402A 40MHz、8kW (キロワード) フラッシュ搭載、64 ピン、16 ビット DSP TMS320LF2403A 40MHz、16kW (キロワード) フラッシュ搭載、64 ピン、16 ビット DSP TMS320LF2406A 40MHz、32kW (キロワード) フラッシュ搭載、100 ピン、16 ビット DSP TMS320LF2407A 40MHz、32kW (キロワード) フラッシュ搭載、144 ピン、16 ビット DSP
設計ツール

C2000-3P-SEARCH — 3P search tool

TI は複数の企業と協力し、TI の C2000 デバイスに対応する多様なソリューションとサービスを提供しています。これらの企業は、各種 C2000 デバイスを使用した量産へと至るお客様の開発工程の迅速化に役立ちます。この検索ツールをダウンロードすると、サード・パーティー各社の概要を手早く参照し、お客様のニーズに適したサード・パーティーを見つけることができます。

このツールは、Applications (アプリケーション) および Flash programming (フラッシュ書き込み) という、ソリューションやサービスに関する 2 種類の大分類を使用しています。

Applications (...)

パッケージ ピン数 ダウンロード
LQFP (VF) 32 オプションの表示

購入と品質

記載されている情報:
  • RoHS
  • REACH
  • デバイスのマーキング
  • リード端子の仕上げ / ボールの原材料
  • MSL 定格 / ピーク リフロー
  • MTBF/FIT 推定値
  • 材質成分
  • 認定試験結果
  • 継続的な信頼性モニタ試験結果
記載されている情報:
  • ファブの拠点
  • 組み立てを実施した拠点

サポートとトレーニング

TI E2E™ フォーラムでは、TI のエンジニアからの技術サポートを提供

コンテンツは、TI 投稿者やコミュニティ投稿者によって「現状のまま」提供されるもので、TI による仕様の追加を意図するものではありません。使用条件をご確認ください。

TI 製品の品質、パッケージ、ご注文に関するお問い合わせは、TI サポートをご覧ください。​​​​​​​​​​​​​​

ビデオ