UCC27532
- Low Cost Gate Driver (offering optimal solution for driving
FET and IGBTs) - Superior Replacement to Discrete Transistor Pair Drive (providing
easy interface with controller) - CMOS Compatible Input Logic Threshold (becomes fixed at VDD above 18 V)
- Split Outputs Allow Separate Turn-On and Turn-Off Tuning
- Enable with Fixed TTL Compatible Threshold
- High 2.5-A Source and 5-A Sink Peak Drive Currents at 18-V VDD
- Wide VDD Range From 10 V up to 35 V
- Input Pins Capable of Withstanding up to -5-V DC Below Ground
- Output Held Low When Inputs are Floating or During VDD UVLO
- Fast Propagation Delays (17-ns typical)
- Fast Rise and Fall Times
(15-ns and 7-ns typical with 1800-pF Load) - Under Voltage Lockout (UVLO)
- Used as a High-Side or Low-Side Driver (if designed with
proper bias and signal isolation) - Low Cost, Space Saving 6-Pin DBV (SOT-23) Package
- Operating Temperature Range of –40°C to 140°C
The UCC27532 is a single-channel, high-speed, gate driver capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn-on effect. The UCC27532 device also features a split-output configuration where the gate-drive current is sourced through OUTH pin and sunk through OUTL pin. This pin arrangement allows the user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the switching slew rates.
The driver has rail-to-rail drive capability and extremely small propagation delay typically 17 ns.
The UCC27532DBV has CMOS input threshold centered 55% rise and 45% fall in regards of VDD at VDD below or equal 18 V. When VDD is above 18 V, the input threshold remains fixed at its maximum level.
The driver has EN pin with fixed TTL compatible threshold. EN is internally pulled up; pulling EN low disables driver, while leaving it open provides normal operation. The EN pin can be used as an additional input with the same performance as the IN pin.
Leaving the input pin of driver open holds the output low. The logic behavior of the driver is shown in the application diagram, timing diagram and input and output logic truth table.
Internal circuitry on VDD pin provides an under voltage lockout function that holds output low until VDD supply voltage is within operating range.
The UCC27532 driver is offered in a 6-pin standard SOT-23 (DBV) package. The device operates over wide temperature range of 40°C to 140°C.
技術資料
種類 | タイトル | 最新の英語版をダウンロード | 日付 | |||
---|---|---|---|---|---|---|
* | データシート | FET および IGBT シングル・ゲート・ドライバ シンクピーク電流: 5A およびソースピーク電流: 2.5A、35VMAX VDD データシート | 2013年 2月 5日 | |||
アプリケーション・ノート | Using a Single-Output Gate-Driver for High-Side or Low-Side Drive (Rev. B) | PDF | HTML | 2023年 9月 8日 | |||
アプリケーション概要 | External Gate Resistor Selection Guide (Rev. A) | 2020年 2月 28日 | ||||
アプリケーション概要 | Understanding Peak IOH and IOL Currents (Rev. A) | 2020年 2月 28日 | ||||
アプリケーション概要 | Implementing a Bipolar Gate Drive for Low-Side IGBTs and SiC FETs in Motor Drive | 2019年 10月 10日 | ||||
その他の技術資料 | Fundamentals of MOSFET and IGBT Gate Driver Circuits (Replaces SLUP169) (Rev. A) | 2018年 10月 29日 | ||||
セレクション・ガイド | 電源 IC セレクション・ガイド 2018 (Rev. R 翻訳版) | 英語版 (Rev.R) | 2018年 9月 13日 | |||
アプリケーション・ノート | UCC27531 35-V Gate Driver for SiC MOSFET Applications (Rev. A) | 2018年 5月 8日 | ||||
アプリケーション概要 | Low-Side Gate Drivers With UVLO Versus BJT Totem-Pole | 2018年 3月 16日 | ||||
その他の技術資料 | FETおよびIGBTシングル・ゲート・ドライバ シンクピーク電流:5Aおよびソースピーク電流: 2.5A、35VMAX VDD | 2014年 4月 3日 | ||||
EVM ユーザー ガイド (英語) | Using the UCC27532EVM-538 (Rev. A) | 2013年 8月 22日 |
設計と開発
その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。
UCC27531EVM-184 — UCC27531 評価モジュール
PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®
設計とシミュレーション向けの環境である PSpice for TI (...)
PMP11303 — 高効率 350W AC/DC 電源、リファレンス・デザイン
PMP30192 — コンボ IC を使用するユニバーサル入力、360W PFC + LLC のリファレンス・デザイン
パッケージ | ピン数 | ダウンロード |
---|---|---|
SOT-23 (DBV) | 6 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL 定格 / ピーク リフロー
- MTBF/FIT 推定値
- 材質成分
- 認定試験結果
- 継続的な信頼性モニタ試験結果
- ファブの拠点
- 組み立てを実施した拠点
推奨製品には、この TI 製品に関連するパラメータ、評価基板、またはリファレンス デザインが存在する可能性があります。