275MIPS で、1536KB フラッシュ、ENET (イーサネット)、USB 搭載、C2000™ デュアル・コア 32 ビット・マイコン (MCU)
製品の詳細
パラメータ
パッケージ|ピン|サイズ
特長
- Master Subsystem — Arm® Cortex®-M3
- 125 MHz
- Embedded memory
- Up to 1MB of flash (ECC)
- Up to 128KB of RAM (ECC or parity)
- Up to 64KB of shared RAM
- 2KB of IPC Message RAM
- Five Universal Asynchronous Receiver/Transmitters (UARTs)
- Four Synchronous Serial Interfaces (SSIs)
and a Serial Peripheral Interface (SPI) - Two Inter-integrated Circuits (I2Cs)
- Universal Serial Bus On-the-Go (USB-OTG) + PHY
- 10/100 ENET 1588 MII
- Two Controller Area Network, D_CAN, modules (pin-bootable)
- 32-channel Micro Direct Memory Access (µDMA)
- Dual security zones (128-bit password per zone)
- External Peripheral Interface (EPI)
- Micro Cyclic Redundancy Check (µCRC) module
- Four general-purpose timers
- Two watchdog timer modules
- Three external interrupts
- Endianness: little endian
- Clocking
- On-chip crystal oscillator and external clock input
- Dynamic Phase-Locked Loop (PLL) ratio changes supported
- 1.2-V digital, 1.8-V analog, 3.3-V I/O design
- Interprocessor Communications (IPC)
- 32 handshaking channels
- Four channels generate IPC interrupts
- Can be used to coordinate transfer of data through IPC Message RAMs
- Up to 142 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins
- Glitch-free I/Os
- Control Subsystem — TMS320C28x 32-bit CPU
- 150 MHz
- C28x core hardware built-in self-test
- Embedded memory
- Up to 512KB of flash (ECC)
- Up to 36KB of RAM (ECC or parity)
- Up to 64KB of shared RAM
- 2KB of IPC Message RAM
- IEEE-754 single-precision Floating-Point Unit (FPU)
- Viterbi, Complex Math, CRC Unit (VCU)
- Serial Communications Interface (SCI)
- SPI
- I2C
- 6-channel Direct Memory Access (DMA)
- 12 Enhanced Pulse Width Modulator (ePWM) modules
- 24 outputs (16 high-resolution)
- Six 32-bit Enhanced Capture (eCAP) modules
- Three 32-bit Enhanced Quadrature Encoder Pulse (eQEP) modules
- Multichannel Buffered Serial Port (McBSP)
- EPI
- One security zone (128-bit password)
- Three 32-bit timers
- Endianness: little endian
- Analog Subsystem
- Dual 12-bit Analog-to-Digital Converters (ADCs)
- Up to 2.88 MSPS
- Up to 24 channels
- Four Sample-and-Hold (S/H) circuits
- Up to six comparators with 10-bit Digital-to-Analog Converter (DAC)
- Package
- 289-ball ZWT New Fine Pitch Ball Grid Array (nFBGA)
- Temperature options:
- T: –40ºC to 105ºC Junction
- S: –40ºC to 125ºC Junction
All trademarks are the property of their respective owners.
概要
The Concerto family is a multicore system-on-chip microcontroller unit (MCU) with independent communication and real-time control subsystems. The F28M36x family of devices is the second series in the Concerto family.
The communications subsystem is based on the industry-standard 32-bit Arm Cortex-M3 CPU and features a wide variety of communication peripherals, including Ethernet 1588, USB OTG with PHY, Controller Area Network (CAN), UART, SSI, I2C, and an external interface.
The real-time control subsystem is based on TI’s industry-leading proprietary 32-bit C28x floating-point CPU and features the most flexible and high-precision control peripherals, including ePWMs with fault protection, and encoders and captures—all as implemented by TI’s TMS320C2000™ Entry performance MCUs and Premium performance MCUs. In addition, the C28-CPU has been enhanced with the addition of the VCU instruction accelerator that implements efficient Viterbi, Complex Arithmetic, 16-bit FFTs, and CRC algorithms.
A high-speed analog subsystem and supplementary RAM memory is shared, along with on-chip voltage regulation and redundant clocking circuitry. Safety considerations also include Error Correction Code (ECC), parity, and code secure memory, as well as documentation to assist with system-level industrial safety certification.
類似しているが機能が同等ではない比較製品
技術資料
設計と開発
追加の事項や他のリソースを参照するには、以下のタイトルをクリックすると、詳細ページを表示できます。ハードウェア開発
概要
The C2000 Experimenter Kits from Texas Instruments are ideal products for initial device exploration and testing. The Concerto H63C2 Experimenter Kit has a docking station that features access to all controlCARD signals, breadboard areas and RS-232 and JTAG connectors. Each kit contains a H63C2 (...)
特長
- Isolated USB JTAG Interface (XDS100v2)
- Micro-USB, Ethernet, and MicroSD communication interfaces
- 180-pin DIMM Interface
- Analog I/O, digital I/O and JTAG signals at DIMM interface
- Single 5V power rail for full operation
概要
TMDSHSECDOCK is a baseboard that provides header pin access to key signals on compatible HSEC180-based controlCARDs. A breadboard area is available for rapid prototyping. Board power can be provided by the provided USB cable or a 5V barrel supply.
特長
- Bread-board like baseboard with HSEC180 controlCARD female connector
- Header pin access to key MCU signals
- Breadboard area for customizable routing and prototyping
- Board power can be provided by the provided USB cable or a 5V barrel supply
概要
Spectrum Digital XDS200 は、TI のプロセッサを対象とする最新の XDS200 デバッグ・プローブ(エミュレータ)ファミリの最初のモデルです。XDS200 ファミリは、超低コストの XDS100 と高性能の XDS560v2 の間で、低コストと高性能の最適バランスを実現します。また、すべての XDS デバッグ・プローブは、ETB(Embedded Trace Buffer、組込みトレース・バッファ)を搭載したすべての ARM と DSP プロセッサに対し、コア・トレースとシステム・トレースをサポートしています。
Spectrum Digital XDS200 は、TI 20 ピン・コネクタ(TI 14 ピン、ARM 10 ピン、ARM 20 ピンを接続するための複数のアダプタ付属)とホスト側の USB 2.0 (...)
特長
XDS200 は、TI のプロセッサを対象とする最新の JTAG デバッグ・プローブ(エミュレータ)ファミリです。高い性能と一般的な機能を搭載した低コスト XDS100 と高性能 XDS560v2 の中間に位置する XDS200 は、TI のマイコン、プロセッサ、ワイヤレス・デバイスのデバッグのためのバランス重視のソリューションを提供します。
XDS200 は、販売開始から長い年月が経過している「XDS510」JTAG デバッガ・ファミリに比べ、データ・スループットが高いほか、ARM シリアル・ワイヤ・デバッグ・モードのサポート機能も追加しており、コスト低減を可能にします。
TI では開発ボードのスペース低減を推進しており、すべての XDS200 派生製品は、ターゲット接続用のプライマリ JTAG コネクティビティとして標準的な TI 20 ピン・コネクタを実装しています。この製品に加えて、すべての派生製品は、TI と ARM の標準的な JTAG ヘッダーに接続するためにモジュラー形式のターゲット構成アダプタも採用しています(付属するアダプタは、モデルによって異なります)。
XDS200 は、従来型の IEEE1149.1(JTAG)、IEEE1149.7(cJTAG)、ARM のシリアル・ワイヤ・デバッグ(SWD)とシリアル・ワイヤ出力(SWO)をサポートしており、+1.5V ~ 4.1V のインターフェイス・レベルで動作します。
IEEE1149.7 つまり Compact JTAG(cJTAG)は、従来型の JTAG を大幅に改良しており、2 本のピンだけで従来型のすべての機能をサポートします。また、TI のワイヤレス・コネクティビティ・マイコンでの利用も可能です。
シリアル・ワイヤ・デバッグ(SWD)とは、同じく 2 本のピンを使用して、JTAG より高速なクロック・レートでデータを転送するデバッグ・モードです。シリアル・ワイヤ出力(SWO)を使用する場合は、もう 1 本のピンを追加して、Cortex M4 マイコンで簡潔なトレース動作を実行することができます。
すべての XDS200 モデルは、ホストへの接続のために、USB2.0 ハイスピード(480Mbps)をサポートしており、一部のモデルではイーサネット 10/100Mbps もサポートしています。また、一部のモデルではターゲット・ボードでの消費電力監視をサポートしています。
XDS200 ファミリには、TI の (...)
概要
The XDS560v2 System Trace is the first model of the XDS560v2 family of high-performance debug probes (emulators) for TI processors. The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7).
The (...)
特長
XDS560v2 is the latest variant of the XDS560 family of high-performance debug probes (emulators) for TI processors. With the fastest speeds and most features of the entire XDS family, XDS560v2 is the most comprehensive solution to debug TI microcontrollers, processors and wireless connectivity (...)
概要
The XDS560v2 System Trace is the first model of the XDS560v2 family of high-performance debug probes (emulators) for TI processors. The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7).
The (...)
特長
-
XDS560v2 is the latest variant of the XDS560 family of high-performance debug probes (emulators) for TI processors. With the fastest speeds and most features of the entire XDS family, XDS560v2 is the most comprehensive solution to debug TI microcontrollers, processors and wireless connectivity (...)
概要
C2000 ギャング・プログラマは、同時に 8 個の同じ C2000 デバイスをプログラムできる C2000 デバイス・プログラマです。C2000 ギャング・プログラマでは、標準の RS-232 または USB 接続を使用してホスト PC に接続できるほか、ユーザーがプロセスのフル・カスタマイズを行うことのできるフレキシブルなプログラミング・オプションが提供されます。
C2000 ギャング・プログラマには、GANG スプリッタと呼ばれるボードが付属しており、C2000 ギャング・プログラマと複数のターゲット・デバイス間の相互接続が可能になります。拡張ボードと 8 個のターゲット・デバイスを接続する 8 本のケーブルが供給されます(JTAG または Spy-Bi-Wire コネクタ経由)。プログラミングは、PC を使用しても、スタンドアロン・デバイスとしても行うことができます。PC 側のグラフィカル・ユーザー・インターフェイスも使用可能であり、DLL ベースです。
代表的なソフトウェア・ファイル
特長
- C2000 デバイスを、RS-232 または USB インターフェイス経由で、迅速に、高い信頼性でプログラムできます
- 数種類のプログラミング・モード:
- - インタラクティブ・モード:PC に接続し、C2000 GANG プログラマ GUI を使用してプログラミング。
- - 画像からのプログラム:設定オプションとコード・ファイルを含むイメージが保存できます。これにより、ユーザーが PCなしで、スタンドアロンで C2000 デバイスをプログラムすることができます。
- - スクリプトからのプログラミング:開発者が、より複雑なプログラム手順を自動化できます。
- 設定、プログラミングおよび量産テストのための直観的 GUI
- イメージ保存用の SD カード・スロット
- PC なしでも簡単にプログラミングできる LCD 画面
- 同時に 8 個のターゲットに対応します
- 現在と将来のすべての C2000 デバイスに対応
概要
ソフトウェア開発
Code Composer Studio™ - Integrated Development Environment for C2000 32-bit Real-time Control MCUs
Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop (...)
設計ツールとシミュレーション
CAD/CAE シンボル
パッケージ | ピン数 | ダウンロード |
---|---|---|
NFBGA (ZWT) | 289 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL rating/ リフローピーク温度
- MTBF/FIT の推定値
- 原材料組成
- 認定試験結果
- 継続的な信頼性モニタ試験結果
おすすめの製品には、この TI 製品に関連するパラメータ、評価モジュール、またはリファレンス・デザインが含まれている場合があります。