10 ビット、デュアル 1.5GSPS またはシングル 3.0GSPS の A/D コンバータ (ADC)
製品の詳細
パラメータ
パッケージ|ピン|サイズ
特長
- Excellent Accuracy and Dynamic Performance
- Pin Compatible with ADC12D1000/1600/1800
- Low Power Consumption, Further Reduced at Lower Fs
- Internally Terminated, Buffered, Differential Analog Inputs
- R/W SPI Interface for Extended Control Mode
- Dual-Edge Sampling Mode, in Which the I- and Q-channels Sample One Input at Twice the Sampling Clock Rate
- Test Patterns at Output for System Debug
- Programmable 15-bit Gain and 12-bit Plus Sign Offset
- Programmable tAD Adjust Feature
- 1:1 Non-demuxed or 1:2 Demuxed LVDS Outputs
- AutoSync Feature for Multi-Chip Systems
- Single 1.9V ± 0.1V Power Supply
- 292-Ball BGA Package (27mm x 27mm x 2.4mm with 1.27mm Ball-Pitch); No Heat Sink Required
All trademarks are the property of their respective owners.
概要
The ADC10D1000/1500 is the latest advance in TI's Ultra-High-Speed ADC family. This low-power, high-performance CMOS analog-to-digital converter digitizes signals at 10-bit resolution for dual channels at sampling rates of up to 1.0/1.5 GSPS (Non-DES Mode) or for a single channel up to 2.0/3.0 GSPS (DES Mode). The ADC10D1000/1500 achieves excellent accuracy and dynamic performance while dissipating less than 2.8/3.6 Watts. The product is packaged in a leaded or lead-free 292-ball thermally enhanced BGA package over the rated industrial temperature range of -40°C to +85°C.
The ADC10D1000/1500 builds upon the features, architecture and functionality of the 8-bit GHz family of ADCs. An expanded feature set includes AutoSync for multi-chip synchronization, 15-bit programmable gain and 12-bit plus sign programmable offset adjustment for each channel. The improved internal track-and-hold amplifier and the extended self-calibration scheme enable a very flat response of all dynamic parameters beyond Nyquist, producing 9.1/9.0 Effective Number of Bits (ENOB) with a 100 MHz input signal and a 1.0/1.5 GHz sample rate while providing a 10-18 Code Error Rate (CER) Dissipating a typical 2.77/3.59 Watts in Non-Demultiplex Mode at 1.0/1.5 GSPS from a single 1.9V supply, this device is specified to have no missing codes over the full operating temperature range.
Each channel has its own independent DDR Data Clock, DCLKI and DCLKQ, which are in phase when both channels are powered up, so that only one Data Clock could be used to capture all data, which is sent out at the same rate as the input sample clock. If the 1:2 Demux Mode is selected, a second 10-bit LVDS bus becomes active for each channel, such that the output data rate is sent out two times slower to relax data-capture timing requirements. The part can also be used as a single 2.0/3.0 GSPS ADC to sample one of the I or Q inputs. The output formatting can be programmed to be offset binary or two's complement and the Low Voltage Differential Signaling (LVDS) digital outputs are compatible with IEEE 1596.3-1996, with the exception of an adjustable common mode voltage between 0.8V and 1.2V to allow for power reduction for well-controlled back planes.
技術資料
設計と開発
追加の事項や他のリソースを参照するには、以下のタイトルをクリックすると、詳細ページを表示できます。ハードウェア開発
概要
One ADC-LD-BB board is included in the hardware kit with the GSPS analog-to-digital converter (ADC) reference boards. Since the analog inputs to the ADC1xDxx00RB are differential and most signal sources are single ended, these balun boards are generally used to achieve (...)
特長
- Balun: B0430J50100AHF
- Balun manufacturer: Anaren
- Frequency range: 400 MHz, 3 GHz
- Impedance ratio: 1:2
- Multilayer construction, low insertion loss, low distortion
概要
One ADC-WB-BB board is included in the hardware kit with the GSPS analog-to-digital converter (ADC) reference boards. Since the analog inputs to the ADC1xDxx00RB are differential and most signal sources are single ended, these balun boards are generally used to achieve (...)
特長
- Balun: TC1-1-13MA+
- Balun manufacturer: Mini-Circuits
- Frequency range: 4.5 MHz, 3 GHz
- Impedance ratio: 1:1
- Wire-wound construction, wideband functionality, good return loss
概要
The ADC10D1500 is the latest advance in Nationals Ultra-High-Speed ADC family. This low-power, high-performance CMOS analog-to-digital converter digitizes signals at 10-bit resolution for dual channels at sampling rates of up to 1.5 GSPS (Non-DES Mode) or for a single channel up to 3.0 GSPS (DES (...)
特長
- Excellent accuracy and dynamic performance
- Low power consumption, further reduced at lower Fs
- Internally terminated, buffered, differential analog inputs
- R/W SPI interface for Extended Control Mode
- Dual-Edge Sampling Mode, in which the I- and Q-channels sample one input at twice the sampling clock rate
- (...)
概要
The TC1 DESIQ Single Balun Board is an accessory board which is designed to drive the ADC1xD1x00RB in DESIQ Mode. It takes a single-ended signal (SMA input) and can drive the I+, I-, Q+ and Q- inputs to the Gig ADC Reference Board.
This board has the Mini-Circuits TC1-1-13MA+ balun on it, which rated (...)
特長
- Rated performance from 4.5 MHz to 3000 MHz
- AC-coupling performed via on-board capacitors
- TC1-DESIQ-SBB Schematic
ソフトウェア開発
While WaveVision 5 software (...)
特長
- Provides 4 plot types: Time Domain (Scope), FFT, 2-tone FFT and Histogram
- Up to 4 data channels per plot
- Multiple plot windows
- Continuous data acquisition
- ACPR Analysis
- FFT averaging
- FFT plot exclusion areas
- Supports hardware and software signal sources
- Provides ability to read/write hardware's control and (...)
設計ツールとシミュレーション
設計とシミュレーション向けの環境である PSpice for TI を使用すると、内蔵のライブラリを活用して、複雑なミックスド・シグナル設計のシミュレーションを実施することができます。完成度の高い最終機器を設計し、レイアウトの確定や製造開始より前に、ソリューションのプロトタイプを製作することができます。この結果、市場投入期間の短縮と開発コストの削減を実現できます。
設計とシミュレーション向けのツールである PSpice for TI の環境内で、各種 TI デバイスの検索、製品ラインアップの参照、テスト・ベンチの起動、設計のシミュレーションを実施し、選定したデバイスをさらに分析することができます。また、複数の TI デバイスを組み合わせてシミュレーションを実行することもできます。
事前ロード済みの複数のモデルで構成されたライブラリ全体に加えて、PSpice for TI ツール内で各種 TI デバイスの最新の技術関連資料に簡単にアクセスすることもできます。開発中のアプリケーションに適したデバイスを選定できたことを確認した後、TI 製品の購入ページにアクセスして、その製品を購入することができます。
PSpice for TI を使用すると、回路の検討から設計の開発や検証まで、作業の進展に合わせて設計サイクルの各段階で、シミュレーションのニーズに適した各種ツールにアクセスできます。コスト不要で入手でき、開発を容易に開始できます。設計とシミュレーションに適した PSpice スイートをダウンロードして、今すぐ設計を開始してください。
開発の開始
- PSpice for TI シミュレータへのアクセスの申請
- ダウンロードとインストール
- シミュレーション方法説明ビデオのご視聴
特長
- Cadence の PSpice テクノロジーを活用
- デジタル・モデル・スイートが付属する事前インストール済みのライブラリを活用して、ワーストケース・タイミング分析を実現可能
- 動的更新により、最新のデバイス・モデルに確実にアクセス可能
- 精度の低下を招かずに、シミュレーション速度を重視して最適化済み
- 複数製品の同時分析をサポート
- OrCAD Capture フレームワークを土台とし、業界で最も幅広く使用されている回路図のキャプチャとシミュレーションの環境へのアクセスを実現
- オフライン作業が可能
- 以下の点を含め、多様な動作条件とデバイス公差にまたがって設計を検証
- 自動的な測定と後処理
- モンテカルロ分析法
- ワーストケース分析
- 熱解析
リファレンス・デザイン
設計ファイル
-
download TIDA-00113 BOM (5 files).zip (827KB)
CAD/CAE シンボル
パッケージ | ピン数 | ダウンロード |
---|---|---|
BGA (NXA) | 292 | オプションの表示 |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL rating/ リフローピーク温度
- MTBF/FIT の推定値
- 原材料組成
- 認定試験結果
- 継続的な信頼性モニタ試験結果
おすすめの製品には、この TI 製品に関連するパラメータ、評価モジュール、またはリファレンス・デザインが含まれている場合があります。